Standards
GOST 27017-86 Fasteners
GOST 27017-86 · General fastener standards
This is an informational translation of a Russian national standard. The Russian original is authoritative.
FASTENERS
TERMS AND DEFINITIONS
GOST 27017-86
(ST SEV 6300-88)
USSR STATE COMMITTEE FOR
PRODUCT QUALITY MANAGEMENT AND STANDARDS
Moscow
State Standard of the Union of Soviet Socialist Republics
| FASTENERS Terms and definitions Fasteners. Terms and definitions | GOST 27017-86 (ST SEV 6300-88) |
|---|
Effective date 01.01.88
This standard establishes terms and definitions of the basic concepts of types of general mechanical engineering fasteners and their structural elements.
The terms established by this standard are mandatory for use in all types of documentation and literature falling within the scope of standardization or using the results of this activity.
This standard shall be applied together with GOST 11708.
One standardized term is established for each concept. The use of synonymous terms for a standardized term is not permitted. Synonymous terms not permitted for use are given in the standard for reference and marked with the note “Ndp”.
For certain standardized terms, the standard provides short forms for reference, which may be used in cases that exclude the possibility of their being interpreted differently.
The definitions given may, if necessary, be modified by introducing derivative characteristics into them, by clarifying the meaning of the terms used in them, and by indicating objects included within the scope of the concept being defined. Such modifications must not alter the scope and content of the concepts defined in this standard.
The standard provides, for reference, foreign-language equivalents for a number of standardized terms in German (D), English (E) and French (F).
The standard includes alphabetical indexes of the terms it contains in Russian and their foreign-language equivalents.
Standardized terms are set in bold type, their short form in regular type, and inadmissible synonyms in italics.
The standard includes an appendix containing the terminology and nomenclature of fasteners in Russian, German, English and French.
(Amended edition, Amendment No. 1).
| Term | Definition |
|---|---|
| GENERAL CONCEPTS | |
| 1. Fastener | A part used to form a joint |
| E. Fastener | |
| 2. Bolt | A fastener in the form of a shank with external thread at one end and a head at the other, forming a joint by means of a nut or a threaded hole in one of the parts being joined |
| D. Schraube | |
| E. Bolt | |
| F. Boulon | |
| 3. Screw | A fastener used to form a joint or to secure parts, made in the form of a shank with external thread at one end and a structural element for transmitting torque at the other. |
| D. Schraube | |
| E. Screw | |
| F. Vis | |
| Note. The structural element of a screw for transmitting torque may be a slotted head, a knurled head, or, in the absence of a head, a slot in the end face of the shank | |
| 4. Wood screw | A fastener in the form of a shank with external special thread, a tapered threaded end, and a head at the other end, forming thread in the hole of the wood or plastic part being joined. |
| D. Holzschraube | |
| E. Wood screw | Note. The special thread has a sharp triangular profile and a groove width greater than the tooth width |
| F. Vis à bois | |
| 5. Stud | A fastener in the form of a cylindrical shank with external thread at both ends or along the entire length of the shank |
| D. Stiftschraube | |
| E. Stud | |
| F. Goujon | |
| 6. Pin | A fastener in the form of a cylindrical or tapered shank used to locate parts during assembly |
| D. Stift | |
| E. Pin | |
| F. Goupille | |
| 7. Nut | A fastener with a threaded hole and a structural element for transmitting torque. |
| D. Mutter | |
| E. Nut | Note. The structural element of a nut for transmitting torque may be a polygon, knurling on the side surface, end or radial holes, slots, etc. |
| F. Ecrou | |
| 8. Washer | A fastener with a hole, placed under a nut or under the head of a bolt or screw to increase the bearing surface and (or) prevent self-loosening |
| D. Scheibe | |
| E. Washer | |
| F. Rondelle | |
| 9. Cotter pin | A fastener in the form of a wire rod of semicircular cross-section, folded double to form a head |
| D. Splint | |
| E. Split pin | |
| F. Goupille | |
| 10. Rivet | A fastener in the form of a smooth cylindrical shank with a head at one end, used to form a permanent joint by forming a head at the other end of the shank through plastic deformation |
| D. Niet | |
| E. Rivet | |
| F. Rivet | |
| TYPES OF FASTENERS | |
| 11. Shoulder bolt | A bolt whose smooth shank diameter exceeds the nominal thread diameter |
| D. Schraube rnit Ansatzschaft | |
| E. Shoulder bolt | |
| F. Corps de boulon renforcée | |
| 12. Eye bolt | A bolt whose head is made as the movable part of a hinge joint |
| D. Augenschraube | |
| E. Eye bolt | |
| F. Corps de boulon à oeil | |
| 13. Fit bolt | A bolt whose smooth shank diameter is determined from the requirement that the joint operate in shear |
| Ndp. Bolt for reamed holes | |
| D. Paßschraube | |
| E. Fit bolt | |
| F. Corps de boulon ajustable | |
| 14. Foundation bolt | A bolt with a specially shaped head, used to fasten equipment to a foundation. |
| D. Steinschraube | |
| E. Foundation holt | Note. The special head shape may be formed by spread tabs of the slotted part of the shank, a bent part of the shank, etc. |
| F. Tige de scellement | |
| 15. Screw with waisted shank | A screw whose smooth shank diameter is smaller than the minor diameter of the thread |
| D. Schraube mit Dehnschaft | |
| E. Screw with waisted shank | |
| F. Vis à tige allégée | |
| 16. Self-tapping screw | A screw that forms special thread in the hole of one of the plastic or metal parts being joined |
| D. Blechschraube | |
| E. Self-tapping screw | |
| F. Vis à tôle | |
| 17. Self-drilling self-tapping screw | A self-tapping screw with a drill-shaped end |
| 18. Set screw | A screw with a specially shaped end, used to secure parts relative to one another |
| E. Set screw | |
| Note. The special end shape may be cylindrical, conical, flat, etc. | |
| 19. Spring pin | A cylindrical pin with a tubular cross-section and a longitudinal slot along its length, rolled from spring steel |
| 20. Slotted nut | A hexagon nut with radial slots for a cotter pin on one of the end faces |
| D. Kronenmutter | |
| E. Hexagon slotted nut | |
| F. Ecrou hexagonal à créneaux | |
| 21. Castle nut | A hexagon nut, part of which is made in the form of a cylinder with radial slots for a cotter pin |
| D. Kronenmutter | |
| E. Hexagon castle nut | |
| F. Ecrou hexagonal à créneaux dégagés | |
| 22. Cap nut | A nut with a spherical and flat end face and a blind threaded hole |
| D. Hutmutter | |
| E. Acorn nut | |
| F. Ecrou borgne à calotte | |
| 23. Wing nut | A nut with flat projecting elements for transmitting torque |
| D. Flügelmutter | |
| E. Wing nut | |
| F. Ecrou à oreilles | |
| 24. Flat washer | A washer with a flat bearing surface |
| D. Scheibe | |
| E. Plain washer | |
| F. Rondelle plate | |
| 25. Spring lock washer | A split circular washer whose ends lie in different planes, used to prevent fasteners from self-loosening through its elastic deformation under load |
| Not permitted: Grover washer | |
| D. Federring | |
| E. Spring washer | |
| F. Rondelle élastique | |
| 26. Lock washer | A washer used to prevent fasteners from self-loosening by means of structural elements. |
| D. Scheibe mit Lappen oder Nasen | |
| E. Tab washer | Note. The structural elements of the washer are tabs, tangs, teeth, etc. |
| F. Frein d’écrou | |
| 27. Hollow rivet | A rivet with a tubular shank |
| 28. Semi-tubular rivet | A rivet whose shank end has a tubular cross-section |
| ELEMENTS OF FASTENERS | |
| 29. Fastener shank | The part of a fastener that directly enters the holes of the parts being joined or is screwed into the material of one of them |
| Shank | |
| 30. Fastener head | The part of a fastener with a shank that serves to transmit torque and (or) form a bearing surface |
| Head | |
| D. Kopf | |
| E. Head | |
| F. Tête | |
| 31. Bolt neck | The smooth part of the bolt shank, cylindrical, oval or square in shape, directly adjoining the head and used for centering the bolt or preventing it from turning |
| Neck | |
| D. Ansatz | |
| E. Neck | |
| F. Collet | |
| 32. Fastener collar | A projection on the bearing surface of a polygonal nut, bolt head or screw head, made in the form of a cylinder or truncated cone with a diameter larger than the diameter of their circumscribed circle |
| Collar | |
| Not permitted: Flange | |
| D. Bund | |
| E. Collar | |
| F. Embase | |
| 33. Fastener bearing projection | An annular projection on the bearing surface of a polygonal nut or bolt head, the diameter of which is smaller than the width across flats. |
| Bearing projection | Note. The width across flats is understood as the distance between opposite faces of a polygonal nut or bolt/screw head, measured in a plane normal to their axis |
| Not permitted: Bearing washer | |
| ”Dead washer” | |
| D. Telleransatz | |
| E. Washer face | |
| F. Collerette | |
| 34. Fastener slot | A specially shaped recess in the end face of a bolt, screw or wood screw head, in the end face of a headless set screw, along the generating line, or in the end face of a nut |
| Slot | |
| Note. The slot shape may be hexagonal, cross-shaped, in the form of a through or blind slit, etc. | |
| 35. Bolt lug | A projection on the bearing surface of the bolt head that prevents it from turning |
| Lug | |
| 36. Bolt tang | A projection on the bearing surface of the bolt head and shank that prevents it from turning |
| Tang | |
| D. Nase | |
| E. Nib | |
| F. Ergot | |
| 37. Gimlet point | The threaded conical end of a wood screw used to cut a thread in a wooden or plastic part when forming a joint |
| E. Gimlet point |
ALPHABETICAL INDEX OF RUSSIAN TERMS
| Bolt | 2 |
|---|---|
| Bolt for reamed holes | 13 |
| Hinged bolt | 12 |
| Fitted bolt | 13 |
| Step bolt | 11 |
| Foundation bolt | 14 |
| Gimlet point | 37 |
| Collar | 32 |
| Fastener collar | 32 |
| Screw | 3 |
| Captive screw | 15 |
| Self-tapping screw | 16 |
| Self-drilling self-tapping screw | 17 |
| Set screw | 18 |
| Fastener bearing projection | 33 |
| Bearing projection | 33 |
| Nut | 7 |
| Wing nut | 23 |
| Cap nut | 22 |
| Castle nut | 21 |
| Slotted nut | 20 |
| Head | 30 |
| Head of a fastener | 30 |
| Rivet | 10 |
| Semi-tubular rivet | 28 |
| Tubular rivet | 27 |
| Fastener | 1 |
| Neck | 31 |
| Neck of bolt | 31 |
| Shank | 29 |
| Shank of a fastener | 29 |
| Tang | 36 |
| Lug of bolt | 36 |
| Flange | 32 |
| Washer | 8 |
| Grower washer | 25 |
| ”Dead” washer | 33 |
| Bearing washer | 33 |
| Flat washer | 24 |
| Spring lock washer | 25 |
| Lock washer | 26 |
| Lug | 35 |
| Tenon of bolt | 35 |
| Slot | 34 |
| Slot of a fastener | 34 |
| Stud | 5 |
| Cotter pin | 9 |
| Pin | 6 |
| Spring pin | 19 |
| Wood screw | 4 |
ALPHABETICAL INDEX OF TERMS IN GERMAN
| Ansatz | 31 |
|---|---|
| Augenschraube | 12 |
| Blechschraube | 16 |
| Bund | 32 |
| Federring | 25 |
| Flügelmulter | 23 |
| Holzschraube | 4 |
| Hutmutter | 22 |
| Kopf | 30 |
| Kronenmutte | 20.21 |
| Mutter | 7 |
| Nase | 36 |
| Niet | 10 |
| Paßschraube | 13 |
| Scheibe | 8.24 |
| Scheibe mit Lappen oder Nasen | 26 |
| Schraube | 2.3 |
| Schraube mit Ansatzschaft | 11 |
| Schraube mit Dehnschaft | 15 |
| Splint | 9 |
| Steinschraube | 14 |
| Stift | 6 |
| Stiftschraube | 5 |
| Telleransatz | 33 |
ALPHABETICAL INDEX OF TERMS IN ENGLISH
| Acorn nut | 22 |
|---|---|
| Bolt | 2 |
| Collar | 32 |
| Eye bolt | 12 |
| Fastener | 1 |
| Fit bolt | 13 |
| Foundation bolt | 14 |
| Gimlet point | 37 |
| Head | 30 |
| Hexagon castle nut | 21 |
| Hexagon slotted nut | 20 |
| Neck | 31 |
| Nib | 36 |
| Nut | 7 |
| Pin | 6 |
| Plain washer | 24 |
| Rivet | 10 |
| Screw | 3 |
| Screw with waisted shank | 15 |
| Self-tapping screw | 16 |
| Set screw | 18 |
| Shoulder bolt | 11 |
| Split pin | 9 |
| Spring washer | 25 |
| Stud | 5 |
| Tab washer | 26 |
| Washer | 8 |
| Washer face | 33 |
| Wing nut | 23 |
| Wood screw | 4 |
ALPHABETICAL INDEX OF TERMS IN FRENCH
| Boulon | 2 |
|---|---|
| Collerette | 33 |
| Collet | 31 |
| Corps de boulon ajustable | 13 |
| Corps de boulon à oeil | 12 |
| Corps de boulon renforcée | 11 |
| Ecrou | 7 |
| Ecrou à oreilles | 23 |
| Ecrou borgne á calotte | 22 |
| Ecrou hexagonal à créneaux | 20 |
| Ecrou hexagonal à créneaux dégagés | 21 |
| Embase | 32 |
| Ergot | 36 |
| Frein d’écrou | 26 |
| Goujon | 5 |
| Goupille | 6.9 |
| Rivet | 10 |
| Rondelle | 8 |
| Rondelle élastique | 25 |
| Rondelle plate | 24 |
| Tête | 30 |
| Tige de scellement | 14 |
| Vis | 3 |
| Vis à bois | 4 |
| Vis à tige allégée | 15 |
| Vis à tôle | 16 |
Appendix
For reference
1. THREAD
| Designation | Drawing |
|---|---|
| 1.1. Thread | |
| 1.2. Tapered thread | |
| 1.3. Self-tapping thread | |
| 1.4. Wood screw thread | |
| 1.5. Metric thread | |
| 1.6. Metric fine-pitch thread |
2. HEAD SHAPES
| Designation | Drawing |
|---|---|
| 2.1. Hexagon head | |
| 2.2. Hexagon head with bearing projection | |
| 2.3. Hexagon head with cylindrical collar | |
| 2.4. Hexagon head with flange | |
| 2.5. Square head | |
| 2.6. Square head with cylindrical collar | |
| 2.7. Triangular head with cylindrical collar | |
| 2.8. Octagon head | |
| 2.9. 12-point head with flange | |
| 2.10. T-head | |
| 2.11. T-head with square neck | |
| 2.12. Round head | |
| 2.13. Low round head | |
| 2.14. Round head with lug | |
| 2.15. Low round head with square neck | |
| 2.16. Round head with oval neck | |
| 2.17. Cylindrical head | |
| 2.18. Cylindrical head with spherical top | |
| 2.19. Low cylindrical head with spherical top | |
| 2.20. Cylindrical rounded head | |
| 2.21. Countersunk head | |
| 2.22. Countersunk head with shoulder | |
| 2.23. Countersunk head with lug | |
| 2.24. Countersunk head with square neck | |
| 2.25. Raised countersunk head | |
| 2.26. Raised countersunk head with shoulder | |
| 2.27. Knurled cylindrical head with straight knurling | |
| 2.28. Knurled cylindrical head with diamond knurling |
3. SHANK SHAPES
| Designation | Drawing |
|---|---|
| 3.1. Normal shank (shank whose diameter equals the nominal thread diameter) | |
| 3.2. Reduced shank (shank whose diameter is approximately equal to the pitch diameter of the thread) | |
| 3.3. Enlarged shank, whose diameter is greater than the nominal thread diameter | |
| 3.4. Thinned shank (shank whose diameter is smaller than the minor diameter of the thread) | |
| 3.5. Stepped shank | |
| 3.6. Hollow shank | |
| 3.7. Semi-hollow shank |
4. ENDS OF BOLTS AND SCREWS
| Designation | Drawing |
|---|---|
| 4.1. End without chamfer | |
| 4.2. Spherical end | |
| 4.3. End with chamfer | |
| 4.4. Conical end | |
| 4.5. Blunt conical end | |
| 4.6. Drilled end | |
| 4.7. Flat end | |
| 4.8. Cylindrical end | |
| 4.9. Shortened cylindrical end | |
| 4.10. Stepped end with sphere | |
| 4.11. Stepped end with cone | |
| 4.12. Tapered blunt-point end of a self-tapping screw with cutting edge | |
| 4.13. Tapered end of a self-tapping screw | |
| 4.14. Flat end of a self-tapping screw | |
| 4.15. End of a thread-forming screw | |
| 4.16. Gimlet point of a wood screw |
5. Elements transmitting rotation
| Designation | Drawing |
|---|---|
| 5.1. Hexagon | |
| 5.2. Square | |
| 5.3. Triangle | |
| 5.4. Octagon | |
| 5.5. Twelve-point | |
| 5.6. Triangular socket | |
| 5.7. Square socket | |
| 5.8. Hex socket | |
| 5.9. Slotted socket | |
| 5.10. Serrated socket | |
| 5.11. Slot | |
| 5.12. Cross recess | |
| 5.13. Wing head | |
| 5.14. Straight knurling | |
| 5.15. Cross knurling | |
| 5.16. Crosswise holes |
6. Bolts and screws with hexagon head
| Designation | Drawing |
|---|---|
| 6.1. Hexagon head bolt | |
| 6.2. Stepped hexagon head bolt | |
| 6.3. Hexagon head set screw with cylindrical point | |
| 6.4. Hexagon head set screw with stepped cone point | |
| 6.5. Hexagon head screw with reduced shank | |
| 6.6. Hexagon head bolt with cylindrical collar | |
| 6.7. Hexagon flange bolt |
7. Screws with square (four-sided) head
| Designation | Drawing |
|---|---|
| 7.1. Square head screw | |
| 7.2. Square head screw with cylindrical collar | |
| 7.3. Square head set screw with cylindrical point | |
| 7.4. Square head set screw with drilled point | |
| 7.5. Square head set screw with cylindrical collar and stepped point with spherical tip |
8. Bolts with triangular head
| Designation | Drawing |
|---|---|
| 8. Triangular head bolt with cylindrical collar |
9. Bolts with octagon head
| Designation | Drawing |
|---|---|
| 9. Octagon head bolt |
10. Bolts with twelve-point head
| Designation | Drawing |
|---|---|
| 10. Twelve-point flange bolt |
11. Bolts with T-head
| Designation | Drawing |
|---|---|
| 11.1. T-head bolt | |
| 11.2. T-head bolt with square neck | |
| 11.3. T-head bolt with lugs under the head |
12. Bolts with round head
| Designation | Drawing |
|---|---|
| 12.1. Low round head bolts with square neck | |
| 12.2. Round head bolt with nib | |
| 12.3. Low round head bolt with nib | |
| 12.4. Round head bolt with oval neck |
13. Bolts with countersunk heads
| Designation | Drawing |
|---|---|
| 13.1. Countersunk head bolt with square neck | |
| 13.2. Countersunk head bolt with nib | |
| 13.3. Tire bolt |
14. Screws with hex socket
| Designation | Drawing |
|---|---|
| 14.1. Cylindrical head screw with hex socket | |
| 14.2. Stepped cylindrical head screw with hex socket | |
| 14.3. Countersunk head screw with hex socket |
15. Screws with slot
| Designation | Drawing |
|---|---|
| 15.1. Cylindrical head screw | |
| 15.2. Cylindrical head screw with rounded top | |
| 15.3. Cylindrical head screw with spherical top | |
| 15.4. Set screw with cylindrical head with spherical top and cylindrical point | |
| 15.5. Stepped screw with cylindrical head with spherical top | |
| 15.6. Screw with cylindrical head with spherical top, with hole in head | |
| 15.7. Screw with reduced cylindrical head with spherical top | |
| 15.8. Countersunk head screw | |
| 15.9. Set screw with countersunk head and cylindrical point | |
| 15.10. Raised countersunk head screw | |
| 15.11. Set screw with raised countersunk head and cylindrical point | |
| 15.12. Countersunk head screw with closed slot | |
| 15.13. Round head screw |
16. Screws with cross recess
| Designation | Drawing |
|---|---|
| 16.1. Cylindrical head screw with spherical top and cross recess | |
| 16.2. Countersunk head screw with cross recess | |
| 16.3. Raised countersunk head screw with cross recess | |
| 16.4. Round head screw with cross recess |
17. Screws with captive parts
| Designation | Drawing |
|---|---|
| 17.1. Hexagon head screw with captive flat washer | |
| 17.2. Hex head screw with captive spring lock washer and flat washer | |
| 17.3. Cylinder head screw with spherical top and captive spring lock washer | |
| 17.4. Raised countersunk head screw with captive lock washer |
18. Various types of bolts and screws
| Designation | Drawing |
|---|---|
| 18.1. Swing bolt | |
| 18.2. Bolt with low round head and lug | |
| 18.3. Bolt with flat head and lug | |
| 18.4. Bolt with countersunk head and two lugs | |
| 18.5. Dog bolt | |
| 18.6. Cap head bolt | |
| 18.7. Tapered bolt | |
| 18.8. Anchor bolt | |
| 18.9. Foundation bolt | |
| 18.10. Wing screw | |
| 18.11. Eye Bolt |
19. Headless set screws
| Designation | Drawing |
|---|---|
| 19.1. Set screw with flat point | |
| 19.2. Set screw with cylindrical point | |
| 19.3. Set screw with drilled point | |
| 19.4. Set screw with cone point | |
| 19.5. Set screw with flat point and hex socket | |
| 19.6. Set screw with cylindrical point and hex socket | |
| 19.7. Set screw with drilled point and hex socket | |
| 19.8. Set screw with cone point and hex socket |
20. Self-tapping screws
| Designation | Drawing |
|---|---|
| 20.1. Self-tapping screw with hex head | |
| 20.2. Self-tapping screw with cylinder head | |
| 20.3. Self-tapping screw with countersunk head | |
| 20.4. Self-tapping screw with raised countersunk head | |
| 20.5. Self-tapping screw with countersunk head and cross recess | |
| 20.6. Self-tapping screw with raised countersunk head and cross recess | |
| 20.7. Self-tapping screw with round cylinder head and cross recess |
21. Wood screws
| Designation | Drawing |
|---|---|
| 21.1. Wood screw with hex head | |
| 21.2. Wood screw with square head | |
| 21.3. Wood screw with round head | |
| 21.4. Wood screw with raised countersunk head | |
| 21.5. Wood screw with countersunk head | |
| 21.6. Wood screw with round head and cross recess | |
| 21.7. Wood screw with raised countersunk head and cross recess | |
| 21.8. Wood screw with countersunk head and cross recess |
22. Thread-cutting screws
| Designation | Drawing |
|---|---|
| 22.1. Thread-cutting screw with hex head | |
| 22.2. Thread-cutting screw with cylinder head | |
| 22.3. Thread-cutting screw with countersunk head | |
| 22.4. Thread-cutting screw with raised countersunk head | |
| 22.5. Thread-cutting screw with spherical cylinder head and cross recess | |
| 22.6. Thread-cutting screw with countersunk head and cross recess | |
| 22.7. Thread-cutting screw with raised countersunk head and cross recess |
23. Thread-forming screws
| Designation | Drawing |
|---|---|
| 23. Thread-forming screw |
24. Screws with knurled head
| Designation | Drawing |
|---|---|
| 24.1. Screw with knurled cylinder head and flat point | |
| 24.2. Screw with knurled cylinder head and cone point | |
| 24.3. Screw with knurled cylinder head and stepped point with cone | |
| 24.4. Screw with knurled cylinder head and drilled point | |
| 24.5. Screw with knurled cylinder head and spherical point | |
| 24.6. Screw with knurled cylinder head and cylindrical point |
25. Pins
| Designation | Drawing |
|---|---|
| 25.1. Parallel pin | |
| 25.2. Parallel pin with internal thread | |
| 25.3. Parallel pin with drilled ends | |
| 25.4. Grooved parallel pin | |
| 25.5. Grooved parallel pin with tapered grooves | |
| 25.6. Split taper pin | |
| 25.7. Taper pin | |
| 25.8. Taper pin with internal thread | |
| 25.9. Taper pin with threaded end | |
| 25.10. Spring pin | |
| 25.11. Threaded pin with flat point and slot | |
| 25.12. Threaded pin with flat point and hex socket | |
| 25.13. Threaded pin with flat cone point and hex socket | |
| 25.14. Threaded pin with cylindrical point and hex socket. | |
| 25.15. Threaded pin with drilled point and hex socket |
26. Threaded studs
| Designation | Drawing |
|---|---|
| 26.1. Threaded stud | |
| 26.2. Threaded stud with reduced shank | |
| 26.3. Threaded stud, full thread | |
| 26.4. Weld stud | |
| 26.5. Tie stud with grooves and hex tail |
RIVETS
| Designation | Drawing |
|---|---|
| 27.1. Round head rivet | |
| 27.2. Low round head rivet | |
| 27.3. Countersunk head rivet | |
| 27.4. Raised countersunk head rivet | |
| 27.5. Low raised countersunk head rivet | |
| 27.6. Flat head rivet | |
| 27.7. Hollow rivet with rounded head | |
| 27.8. Hollow rivet with flat head | |
| 27.9. Hollow rivet with countersunk head | |
| 27.10. Hollow rivet with flat head | |
| 27.11. Hollow rivet with countersunk head | |
| 27.12. Semi-hollow rivet with round head |
NUTS
| Designation | Drawing |
|---|---|
| 28.1. Hexagon nut | |
| 28.2. Low hexagon nut | |
| 28.3. Hexagon nut with cylindrical collar | |
| 28.4. Hexagon flange nut | |
| 28.5. Hexagon nut with bearing washer | |
| 28.6. Hexagon weld nut | |
| 28.7. Square nut | |
| 28.8. Low square nut | |
| 28.9. Anchor nut | |
| 28.10. Square nut with cylindrical collar | |
| 28.11. Square weld nut | |
| 28.12. Triangular nut with cylindrical collar | |
| 28.13. Octagonal nut | |
| 28.14. Twelve-point flange nut | |
| 28.15. Self-locking nut with deformed thread | |
| 28.16. Self-locking nut with polymer ring insert | |
| 28.17. Hexagon slotted nut | |
| 28.18. Hexagon castle nut | |
| 28.19. Low hexagon castle nut | |
| 28.20. Cap nut | |
| 28.21. Knurled nut | |
| 28.22. Round nut with face slot | |
| 28.23. Slotted nut | |
| 28.24. Round nut with radial holes | |
| 28.25. Round nut with face holes for wrench | |
| 28.26. Wing nut |
WASHERS
| Designation | Drawing |
|---|---|
| 29.1. Round flat washer | |
| 29.2. Square washer | |
| 29.3. Round washer with square hole | |
| 29.4. Taper washer | |
| 29.5. Spring lock washer | |
| 29.6. Spring lock washer with bent ends | |
| 29.7. Double-coil spring lock washer | |
| 29.8. Curved spring washer | |
| 29.9. Lock washer with external teeth | |
| 29.10. Lock washer with internal teeth | |
| 29.11. Lock washer with teeth for countersunk and raised countersunk head screws | |
| 29.12. Wave spring washer | |
| 29.13. Spring lock washer with external teeth | |
| 29.14. Spring lock washer with internal teeth | |
| 29.15. Spring lock washer with teeth for countersunk and raised countersunk head screws | |
| 29.16. Lock washer with two tabs | |
| 29.17. Lock washer with external lug | |
| 29.18. Lock washer with tab | |
| 29.19. Lock washer with internal lug |
COTTER PINS
| Designation | Drawing |
|---|---|
| 30. Cotter pin |
II. ALPHABETICAL INDEX OF FASTENER TERMS AND NAMES IN RUSSIAN
| Wing nut | 5.13 |
|---|---|
| Anchor Bolt | 18.8 |
| Tapered bolt | 18.7 |
| Spike bolt | 18.5 |
| Hinged bolt | 18.1 |
| Octagonal head bolt | 9 |
| Twelve-point flange head bolt | 10 |
| Cap head bolt | 18.6 |
| Low round head bolt with square neck | 12.1 |
| Low round head bolt with lug | 12.3 |
| Low round head bolt with pin | 18.2 |
| Flat head bolt with pin | 18.3 |
| Round head bolt with oval neck | 12.4 |
| Round head bolt with lug | 12.2 |
| Countersunk head bolt with square neck | 13.1 |
| Countersunk head bolt with two pins | 18.4 |
| Countersunk head bolt with lug | 13.2 |
| T-head bolt | 11.1 |
| T-head bolt with ribs under head | 11.3 |
| T-head bolt with square neck | 11.2 |
| Bolt with triangular head and cylindrical collar | 8 |
| Stepped hex head bolt | 6.2 |
| Hex head bolt | 6.1 |
| Hex flange bolt | 6.7 |
| Hex head bolt with cylindrical collar | 6.6 |
| Foundation bolt | 18.9 |
| Tire bolt | 13.3 |
| Wood screw gimlet point | 4.16 |
| Wing screw | 18.10 |
| Thread-forming screw | 23 |
| Thread-forming screw with raised countersunk head | 22.4 |
| Thread-cutting screw with raised countersunk head and cross recess | 22.7 |
| Thread-cutting screw with countersunk head | 22.3 |
| Thread-cutting screw with countersunk head and cross recess | 22.6 |
| Thread-cutting screw with cylinder head | 22.2 |
| Thread-cutting screw with domed cylinder head and cross recess | 22.5 |
| Thread-cutting screw with hex head | 22.1 |
| Self-tapping screw with raised countersunk head | 20.4 |
| Self-tapping screw with raised countersunk head and cross recess | 20.6 |
| Self-tapping screw with countersunk head | 20.3 |
| Self-tapping screw with countersunk head and cross recess | 20.5 |
| Self-tapping screw with cylinder head | 20.2 |
| Self-tapping screw with rounded cylinder head and cross recess | 20.7 |
| Self-tapping screw with hex head | 20.1 |
| Square head screw | 7.1 |
| Square head screw with cylindrical collar | 7.2 |
| Round head screw | 15.13 |
| Round head screw with cross recess | 16.4 |
| Raised countersunk head screw | 15.10 |
| Raised countersunk head screw with cross recess | 16.3 |
| Raised countersunk head screw with captive lock washer | 17.4 |
| Countersunk head screw | 15.8 |
| Countersunk head screw with cross recess | 16.2 |
| Countersunk head screw with closed slot | 15.12 |
| Countersunk head screw with hex socket | 14.3 |
| Knurled cylinder head screw with drilled end | 24.4 |
| Knurled cylinder head screw with conical end | 24.2 |
| Knurled cylinder head screw with flat end | 24.1 |
| Knurled cylinder head screw with stepped end and cone | 24.3 |
| Knurled cylinder head screw with spherical end | 24.5 |
| Knurled cylinder head screw with cylindrical end | 24.6 |
| Stepped domed cylinder head screw | 15.5 |
| Stepped cylinder head screw with hex socket | 14.2 |
| Reduced domed cylinder head screw | 15.7 |
| Cylinder head screw | 15.1 |
| Domed cylinder head screw | 15.3 |
| Domed cylinder head screw with cross recess | 16.1 |
| Domed cylinder head screw with captive spring lock washer | 17.3 |
| Domed cylinder head screw with hole in head | 15.6 |
| Cylinder head screw with hex socket | 14.1 |
| Rounded cylinder head screw | 15.2 |
| Hex head screw with captive flat washer | 17.1 |
| Hex head screw with captive spring and flat washers | 17.2 |
| Hex head screw with reduced shank | 6.5 |
| Set screw with drilled end | 19.3 |
| Set screw with drilled end and hex socket | 19.7 |
| Set screw with square head and drilled end | 7.4 |
| Set screw with square head, cylindrical collar and stepped domed end | 7.5 |
| Set screw with square head and cylindrical end | 7.3 |
| Set screw with conical end | 19.4 |
| Set screw with conical end and hex socket | 19.8 |
| Set screw with flat end | 19.1 |
| Set screw with flat end and hex socket | 19.5 |
| Set screw with raised countersunk head and cylindrical end | 15.11 |
| Set screw with countersunk head and cylindrical end | 15.9 |
| Set screw with cylindrical end | 19.2 |
| Set screw with cylindrical end and hex socket | 19.6 |
| Set screw with domed cylinder head and cylindrical end | 15.4 |
| Set screw with hex head and stepped conical end | 6.4 |
| Set screw with hex head and cylindrical end | 6.3 |
| Octagon | 5.4 |
| Anchor nut | 28.9 |
| Wing nut | 28.26 |
| Octagonal nut | 28.13 |
| 12-point flange nut | 28.14 |
| Square nut | 28.7 |
| Low square nut | 28.8 |
| Square weld nut | 28.11 |
| Square nut with cylindrical collar | 28.10 |
| Cap nut | 28.20 |
| Round nut with end holes for wrench | 28.25 |
| Round nut with radial holes | 28.24 |
| Round nut with face slot | 28.22 |
| Knurled nut | 28.21 |
| Self-locking nut with deformed thread | 28.15 |
| Self-locking nut with polymer ring insert | 28.16 |
| Triangular nut with cylindrical collar | 28.12 |
| Hexagon nut | 28.1 |
| Hexagon slotted nut | 28.18 |
| Hexagon thin nut | 28.2 |
| Hexagon thin slotted nut | 28.19 |
| Hexagon weld nut | 28.6 |
| Hexagon slotted nut | 28.17 |
| Hexagon nut with bearing washer | 28.5 |
| Hexagon flange nut | 28.4 |
| Hexagon nut with cylindrical collar | 28.3 |
| Slotted nut | 28.23 |
| Octagon head | 2.8 |
| 12-point flange head | 2.9 |
| Square head | 2.5 |
| Square head with cylindrical collar | 2.6 |
| Low round head | 2.13 |
| Low round head with square neck | 2.15 |
| Low cylinder head with spherical top | 2.19 |
| Round head | 2.12 |
| Round head with oval neck | 2.16 |
| Round head with lug | 2.14 |
| Raised countersunk head | 2.25 |
| Raised countersunk head with shoulder | 2.26 |
| Countersunk head | 2.21 |
| Countersunk head with shoulder | 2.22 |
| Countersunk head with square neck | 2.24 |
| Countersunk head with lug | 2.23 |
| Knurled cylinder head with straight knurling | 2.27 |
| Knurled cylinder head with diamond knurling | 2.28 |
| Cylinder head with spherical top | 2.18 |
| T-head | 2.10 |
| T-head with square neck | 2.11 |
| Triangular head with cylindrical collar | 2.7 |
| Cylinder head | 2.17 |
| Rounded cylinder head | 2.20 |
| Hexagon head | 2.1 |
| Hexagon flange head | 2.4 |
| Hexagon head with bearing washer | 2.2 |
| Hexagon head with cylindrical collar | 2.3 |
| 12-point socket | 5.5 |
| Semi-tubular rivet with flat head | 27.10 |
| Semi-tubular rivet with round head | 27.12 |
| Semi-tubular rivet with countersunk head | 27.11 |
| Rivet with flat head | 27.6 |
| Rivet with round head | 27.1 |
| Rivet with low round head | 27.2 |
| Rivet with raised countersunk head | 27.4 |
| Rivet with low raised countersunk head | 27.5 |
| Rivet with countersunk head | 27.3 |
| Tubular rivet with flat head | 27.8 |
| Tubular rivet with countersunk head | 27.9 |
| Tubular rivet with rounded head | 27.7 |
| Square | 5.2 |
| End without chamfer | 4.1 |
| Drilled end | 4.6 |
| Tapered end | 4.4 |
| Blunt tapered end | 4.5 |
| Flat end | 4.7 |
| End of thread-forming screw | 4.15 |
| Tapered end of self-tapping screw | 4.13 |
| Blunt tapered end of self-tapping screw with cutting edge | 4.12 |
| Flat end of self-tapping screw | 4.14 |
| Stepped end with cone | 4.11 |
| Stepped end with sphere | 4.10 |
| End with chamfer | 4.3 |
| Spherical end | 4.2 |
| Cylindrical end | 4.8 |
| Shortened cylindrical end | 4.9 |
| Cross holes | 5.16 |
| Thread | 1.1 |
| Tapered thread | 1.2 |
| Metric thread | 1.5 |
| Metric fine-pitch thread | 1.6 |
| Self-tapping thread | 1.3 |
| Wood screw thread | 1.4 |
| Straight knurling | 5.14 |
| Diamond knurling | 5.15 |
| Eye Bolt | 18.11 |
| Normal shank | 3.1 |
| Semi-hollow shank | 3.7 |
| Hollow shank | 3.6 |
| Stepped shank | 3.5 |
| Enlarged shank | 3.3 |
| Reduced shank | 3.2 |
| Thinned shank | 3.4 |
| Triangle | 5.3 |
| Square recess | 5.7 |
| Triangular recess | 5.6 |
| Hexagon recess | 5.8 |
| Square washer | 29.2 |
| Tapered washer | 29.4 |
| Round washer with square hole | 29.3 |
| Round flat washer | 29.1 |
| Spring lock washer | 29.5 |
| Wave spring washer | 29.12 |
| Double-coil spring washer | 29.7 |
| Curved spring washer | 29.8 |
| Spring washer with bent ends | 29.6 |
| Internal-tooth spring washer | 29.14 |
| Spring washer with teeth for countersunk and raised countersunk head screws | 29.15 |
| External-tooth spring washer | 29.13 |
| Internal-tooth lock washer | 29.10 |
| Lock washer with internal tab | 29.19 |
| Lock washer with two tabs | 29.16 |
| Lock washer with teeth for countersunk and raised countersunk head screws | 29.11 |
| Lock washer with tab | 29.18 |
| External-tooth lock washer | 29.9 |
| Lock washer with external tab | 29.17 |
| Hexagon | 5.1 |
| Cross recess | 5.12 |
| Slot | 5.11 |
| Stud | 26.1 |
| Weld stud | 26.4 |
| Stud threaded full length | 26.3 |
| Tie stud with grooves and hexagon shank | 26.5 |
| Stud with thinned shank | 26.2 |
| Cotter pin | 30 |
| Taper pin | 25.7 |
| Split taper pin | 25.6 |
| Taper pin with internal thread | 25.8 |
| Taper pin with threaded end | 25.9 |
| Spring pin | 25.10 |
| Threaded pin with drilled end and hexagon socket | 25.15 |
| Threaded pin with blunt conical end and hexagon socket | 25.13 |
| Threaded pin with flat end and hexagon socket | 25.12 |
| Threaded pin with flat end and slot | 25.11 |
| Threaded pin with cylindrical end and hexagon socket | 25.14 |
| Cylindrical pin | 25.1 |
| Grooved cylindrical pin | 25.4 |
| Grooved cylindrical pin with tapered grooves | 25.5 |
| Cylindrical pin with internal thread | 25.2 |
| Cylindrical pin with drilled ends | 25.3 |
| Wood screw with square head | 21.2 |
| Wood screw with round head | 21.3 |
| Wood screw with round head and cross recess | 21.6 |
| Wood screw with raised countersunk head | 21.4 |
| Wood screw with raised countersunk head and cross recess | 21.7 |
| Wood screw with countersunk head | 21.5 |
| Wood screw with countersunk head and cross recess | 21.8 |
| Wood screw with hexagon head | 21.1 |
III. INDEX OF FASTENER TERMS AND NAMES IN GERMAN
| Gewinde | 1.1. |
|---|---|
| Kegliges (konisches) Gewinde | 1.2. |
| Blechschraubengewinde | 1.3. |
| Holzschraubengewinde | 1.4. |
| metrisches Gewinde | 1.5. |
| metrisches Feingewinde | 1.6. |
| Sechskantkopf | 2.1. |
| Sechskantkopf mit Telleransalz | 2.2. |
| Sechskantkopf mit Bund | 2.3. |
| Sechskantkopf mit Flansch (Flanschkopf) | 2.4. |
| Vierkantkopf | 2.5. |
| Vierkantkopf mit Bund | 2.6. |
| Dreikantkopf mit Bund | 2.7. |
| Achtkantkopf | 2.8. |
| Zwölfkantkopf mit Flansch | 2.9. |
| Hammerkopf | 2.10. |
| Hammerkopf mit Vierkantansatz | 2.11. |
| Halbrundkopf | 2.12. |
| Flachrundkopf | 2.13. |
| Halbrundkopf mit Nase | 2.14. |
| Flachrundkopf mit Vierkantansatz | 2.15. |
| Halbrundkopf mit Ovalansatz | 2.16. |
| Zylinderkopf | 2.17. |
| Linsenzylinderkopf | 2.18. |
| Linsenkopf | 2.19. |
| Flachkopf | 2.20. |
| Senkkopf | 2.21. |
| abgesetzter mit Senkkopf | 2.22. |
| Senkkopf mit Nase | 2.23. |
| Sekkopf mit Vierkantansatz | 2.24. |
| Linsensenkkopf | 2.25. |
| abgesetzter Linsensenkkopf | 2.26. |
| Rändelkopf | 2.27. |
| Kordelkopf | 2.28. |
| Dickschaft (Schaftdurchmesser = Gewindedurchmesser) | 3.1. |
| Dünnschaft (Schaftdurchmesser ≈ Flankendurchmesser) | 3.2. |
| Paßschaft (Schaftdurchmesser > Gewindedurchmesser) | 3.3. |
| Dehnschaft (Schaftdurchmesser < Kerndurchmesser) | 3.4. |
| Ansatzschaft | 3.5. |
| Hohlschaft | 3.6. |
| Halbhohlschaft | 3.7. |
| ohne Kuppe | 4.1. |
| Linsenkuppe | 4.2. |
| Kegelkuppe | 4.3. |
| Spitze | 4.4. |
| Spitze, abgeflacht | 4.5. |
| Ringschneide | 4.6. |
| Kegelstumpf | 4.7. |
| Zapfen | 4.8. |
| Kernansatz | 4.9. |
| Ansatzkuppe | 4.10. |
| Ansatzspitze, abgeflacht | 4.11. |
| Schneidschraubenende mit Schabenut | 4.12. |
| Blechschrauben - Spitze | 4.13. |
| Blechschrauben - Zapfen | 4.14. |
| Gewindeformendes Schraubenende | 4.15. |
| Spitze (Nagelbohrer) | 4.16. |
| Sechskant | 5.1. |
| Vierkant | 5.2. |
| Dreikant | 5.3. |
| Achtkant | 5.4. |
| Zwölfkant | 5.5. |
| Innendreikant | 5.6. |
| Innenvierkant | 5.7. |
| Innensechskant | 5.8. |
| Innenkeilprofil | 5.9. |
| Innenzwölfzahn | 5.10. |
| gerader Schlitz | 5.11. |
| Kreuzschlitz | 5.12. |
| Flügel | 5.13. |
| Rändel | 5.14. |
| Kordel | 5.15. |
| Kreuzloch | 5.16. |
| Sechskantschraube | 6.1. |
| Sechskant - Paßschraube | 6.2. |
| Sechskantschraube mit Zapfen | 6.3. |
| Sechskantschrauhe mit Ansatzspitze | 6.4. |
| Sechskantschraube mit Dehnschaft | 6.5. |
| Sechskantschraube mit Bund | 6.6. |
| Sechskantschraube mit Flansch | 6.7. |
| Vierkantschraube | 7.1. |
| Vierkantschrauhe mit Bund | 7.2. |
| Vierkantschraube mit Zapfen | 7.3. |
| Vierkantschraube mit Ringschneide | 7.4. |
| Vierkantschraube mit Bund und Ansatzkuppe | 7.5. |
| Dreikantschraube | 8. |
| Achtkantschraube | 9. |
| Zwölfkantschraube mit Flansch | 10. |
| Hammerschraube | 11.1. |
| Hammerschraube mit Vierkantansatz | 11.2. |
| Hammerschraube mit Nase | 11.3. |
| Flachrundschraube mit Vierkantansatz | 12.1. |
| Halbrundschraube mit Nase | 12.2. |
| Flachrundschraube mit Nase | 12.3. |
| Halbrundschraube mit Ovalansatz | 12.4. |
| Senkschraube mit Vierkantansatz | 13.1. |
| Senkschraube mit Nase | 13.2. |
| Kegelsenkschraube | 13.3. |
| Zylinderschraube mit Innensechskant | 14.1. |
| Zylinderschraube mit Innensechskant und Ansatzschaft | 14.2. |
| Senkschrauben mit Innensechskant | 14.3. |
| Zylinderschraube mit Schlitz | 15.1. |
| Flachkopfschraube mit Schlitz | 15.2. |
| Linsenzylinderschraube mit Schlitz | 15.3. |
| Linsenzylinderschraube mit Schlitz und Zapfen | 15.4. |
| Linsenzylinderschraube mit Schlitz und Ansatz | 15.5. |
| Linsenzylinderschraube mit Schlitz und Kreuzloch | 15.6. |
| Linsenzylinderschraube mit Schlitz und kleinem Kopf | 15.7. |
| Senkschraube mit Schlitz | 15.8. |
| Senkschraube mit Schlitz und Zapfen | 15.9. |
| Linsensenkschraube mit Schlitz | 15.10. |
| Linsensenkschraube mit Schlitz und Zapfen | 15.11. |
| Senkschraube mit Halteschlitz | 15.12. |
| Halbrundschraube mit Schlitz | 15.13. |
| Linsenschraube mit Kreuzschlitz und Dehnschaft | 16.1. |
| Senkschraube mil Kreuzschlitz | 16.2. |
| Linsensenkschraube mit Kreuzschlitz | 16.3. |
| Flachkopfschraube mit Kreuzschlitz | 16.4. |
| Sechskantschraube mit unverlierbarer Scheibe | 17.1. |
| Sechskantschraube mit unverlierbarem Federring und Scheibe | 17.2. |
| Linsenzylinderschraube mit unverlierbarem Federring | 17.3. |
| Linsensenkschraube mit unverlierbarer Fächerscheibe | 17.4. |
| Augenschraube | 18.1. |
| Bogenklammerschraube | 18.2. |
| Flachklammerschraube | 18.3. |
| Tellerschraube mit Nasen | 18.4. |
| Hakenschraube | 18.5. |
| Hutschraube | 18.6. |
| Kegelschraube | 18.7. |
| Steinschraube | 18.8. |
| Steinschraube | 18.9. |
| Flügelschraube | 18.10. |
| Ringschraube | 18.11. |
| Gewindestift mit Schlitz und Kegelstumpf | 19.1. |
| Gewindestift mit Schlitz und Zapfen | 19.2. |
| Gewindestift mit Schlitz und Ringschneide | 19.3. |
| Gewindestift mit Schlitz und Spitze | 19.4. |
| Gewindestift mit Innensechskant und Kegelstumpf | 19.5. |
| Gewindestift mit Innensechskant und Zapfen | 19.6. |
| Gewindestift mit Innensechskant und Ringschneide | 19.7. |
| Gewindestifl mil Innensechskant und Spitze | 19.8. |
| Sechskantblechschraube | 20.1. |
| Zylinderblechschraube mit Schlitz | 20.2. |
| Senkblechschraube mit Schlitz | 20.3. |
| Linsensenkblechschraube mit Schlitz | 20.4. |
| Senkblechschraube mit Kreuzschlitz | 20.5. |
| Linsensenkblechschraube mit Kreuzschlitz | 20.6. |
| Flachkopf-Blechschraube mit Kreuzschlitz | 20.7. |
| Sechskantholzschraube | 21.1. |
| Vierkantholzschraube | 21.2. |
| Halbrundholzschraube mit Schlitz | 21.3. |
| Linsensenkbolzschraube mit Schlitz | 21.4. |
| Senkholzschraube mit Schlitz | 21.5. |
| Halbrundholzschraube mit Kreuzschlitz | 21.6. |
| Linsensenkholzschraube mit Kreuzschlitz | 21.7. |
| Senkholzschraube mit Kreuzschlitz | 21.8. |
| Sechskant-Schneidschraube | 22.1. |
| Zylinder-Schneidschraube mit Schlitz | 22.2. |
| Senk-Schneidschraube mit Schlitz | 22.3. |
| Linsensenk-Schneidschraube mit Schlitz | 22.4. |
| Linsenzylinder-Schneidschraube mit Kreuzschlitz | 22.5. |
| Senk-Schneidschraube mit Kreuzschlitz | 22.6. |
| Linsensenk-Schneidschraube mit Kreuzschlitz | 22.7. |
| Sechskantschraube, gewindefurchend | 23. |
| Rändelschraube | 24.1. |
| Rändelschraube mit Spitze | 24.2. |
| Rändelschraube mit Ansatzspitze | 24.3. |
| Rändelschraube mit Ringschneide | 24.4. |
| Rändelschraube mit Linsenkuppe | 24.5. |
| Rändelschraube mit Zapfen | 24.6. |
| Zylinderstift | 25.1. |
| Zylinderstift mit Innengewinde | 25.2. |
| Nietstift | 25.3. |
| Zylinderkerbstift | 25.4. |
| Kegelkerbstift | 25.5. |
| Kegelstift mit Spreizende | 25.6. |
| Kegelstift | 25.7. |
| Kegelstift mit Innengewinde | 25.8. |
| Kegelstift mit Gewindezapfen | 25.9. |
| Spannstift | 25.10. |
| Gewindestift mit Schlitz, Schaft und Kegelstumpf | 25.11. |
| Gewindestift mit Innensechskant, Schaft und Kegelstumpf | 25.12. |
| Gewindestift mit Innensechskant, Schaft und Spitze | 25.13. |
| Gewindestift mit Innensechskant, Schaft und Zapfen | 25.14. |
| Gewindestift mit Innensechskant, Schaft und Ringschneide | 25.15. |
| Stiftschraube | 26.1. |
| Stiftschraube mit Dehnschaft | 26.2. |
| Gewindebolzen | 26.3. |
| Anschweißende | 26.4. |
| Schraubenbolzen ohne Dehnschaft und Zapfen | 26.5. |
| Halbrundniet | 27.1. |
| Flachrundniet | 27.2. |
| Senkniet | 27.3. |
| Linsenniet | 27.4. |
| flacher Linsenniet | 27.5. |
| Flachkopfniet | 27.6. |
| Hohlniet mit Linsenkopf | 27.7. |
| Hohlniet mit Flachkopf | 27.8. |
| Hohlniet mit Senkkopf | 27.9. |
| Halb-Hohlniet mit Flachkopf | 27.10. |
| Halb-Hohlniet mit Senkkopf | 27.11. |
| Halb-Hohlniet mit Halbrundkopf | 27.12. |
| Sechskantmutter | 28.1. |
| Flache Sechskantmutter | 28.2. |
| Sechskantmutter mit Bund | 28.3. |
| Sechskantmutter mit Flansch | 28.4. |
| Sechskantmutter mil Ansatz | 28.5. |
| Sechskant-Anschweißmutter | 28.6. |
| Vierkantmutter | 28.7. |
| Flache Vierkantmutter | 28.8. |
| Ankermutter | 28.9. |
| Vierkantmutter mit Bund | 28.10. |
| Vierkant-Anschweißmutter | 28.11. |
| Dreikantmutter mit Bund | 28.12. |
| Achtkantmutter | 28.13. |
| Zwölfkantmutter mit Flansch | 28.14. |
| Sechskantmutter mit Klemmteil, ganzmetallisch | 28.15. |
| Sechskantmutter mit Klemmteil, mit nichtmetallischem Einsatz | 28.16. |
| Kronenmutter | 28.17. |
| Kronenmutter | 28.18. |
| Flache Kronenmutter | 28.19. |
| Hutmutter | 28.20. |
| Rändelmutter | 28.21. |
| Schlitzmutter | 28.22. |
| Nutmutter | 28.23. |
| Kreuzlochmutter | 28.24. |
| Zweilochmulter | 28.25. |
| Flügelmutter | 28.26. |
| Scheibe | 29.1. |
| Vierkantscheibe | 29.2. |
| Scheibe mit Vierkantloch | 29.3. |
| Keilscheibe | 29.4. |
| Federring | 29.5. |
| Federring, aufgebogen | 29.6. |
| Mehrfachfederring | 29.7. |
| Federscheibe, gewölbt | 29.8. |
| Fächerscheibe, außen gezahnt | 29.9. |
| Fächerscheibe, innen gezahnt | 29.10. |
| Fächerscheibe, außen gezahnt, keglig | 29.11. |
| Federscheibe, gewellt | 29.12. |
| Zahnscheibe, innen gezahnt | 29.13. |
| Zahnscheibe, außen gezahnt | 29.14. |
| Zahnscheibe, außen gezahnt, keglig | 29.15. |
| Sicherungsblech mit zwei Lappen | 29.16. |
| Sicherungsblech mit Nase, außen | 29.17. |
| Sicherungsblech mit Lappen | 29.18. |
| Sicherungsblech mit Nase, innen | 29.19. |
| Splint | 30. |
IV. INDEX OF FASTENER TERMS AND NAMES IN ENGLISH
| Screw thread | 1.1. |
|---|---|
| Taper screw thread | 1.2. |
| Tapping screw thread | 1.3. |
| Wood screw thread | 1.4. |
| Metric thread (SI) | 1.5. |
| Metric fine pitch thread | 1.6. |
| Hexagon head | 2.1. |
| Hexagon head with washer face | 2.2. |
| Hexagon head with collar | 2.3. |
| Hexagon head with flange | 2.4. |
| Square head | 2.5. |
| Square head with collar | 2.6. |
| Triangle head with collar | 2.7. |
| Octagonal head | 2.8. |
| 12point flange head | 2.9. |
| T-head | 2.10. |
| T-head with square neck | 2.11. |
| Round head | 2.12. |
| Mushroom head | 2.13. |
| Round head with nib | 2.14. |
| Mushroom head with square neck | 2.15. |
| Round head with oval neck | 2.16. |
| Cheese head | 2.17. |
| Raised cheese head | 2.18. |
| Binding head | 2.19. |
| Pan head | 2.20. |
| Countersunk head | 2.21. |
| Undercut countersunk head | 2.22. |
| Countersunk head with nib | 2.23. |
| Countersunk head with square neck | 2.24. |
| Raised countersunk heart | 2.25. |
| Undercut raised countersunk head | 2.26. |
| Straight knurled head | 2.27. |
| Diamond knurled head | 2.28. |
| Normal shank | 3.1. |
| Reduced shank | 3.2. |
| Increased shank | 3.3. |
| Waisted shank | 3.4. |
| Shoulder | 3.5. |
| Tubular shank | 3.6. |
| Semi-tubular shank | 3.7. |
| As-rolled end | 4.1. |
| Rounded end | 4.2. |
| Chamfered end | 4.3. |
| Cone point | 4.4. |
| Truncated cone point | 4.5. |
| Cup point | 4.6. |
| Flat point | 4.7. |
| Long dog point | 4.8. |
| Short dog point | 4.9. |
| Short dog point with rounded end | 4.10. |
| Short dog point with truncated cone end | 4.11. |
| Scrape point | 4.12. |
| 4.14. End for self-tapping screw | 4.13. |
| End for thread rolling screw | 4.15. |
| Gimlet | 4.16. |
| Hexagon | 5.1. |
| Square | 5.2. |
| Triangle | 5.3. |
| Octagon | 5.4. |
| 12point | 5.5. |
| Triangle | 5.6. |
| Square socket | 5.7. |
| Hexagon socket | 5.8. |
| Six-spline socket | 5.9. |
| 12point socket | 5.10. |
| Slot | 5.11. |
| Cross recess | 5.12. |
| Wing | 5.13. |
| Straight knurl | 5.14. |
| Diamond knurl | 5.15. |
| Cross hole | 5.16. |
| Hexagon holt | 6.1. |
| Hexagon fit bolt | 6.2. |
| Hexagon set screw with full dog point | 6.3. |
| Hexagon set screw with half dog point and flat cone point | 6.4. |
| Hexagon screw with waisted shank | 6.5. |
| Hexagon bolt with collar | 6.6. |
| Hexagon bolt with flange | 6.7. |
| Square head bolt | 7.1. |
| Square head bolt with collar | 7.2. |
| Square set screw with half dog point | 7.3. |
| Square set screw with cup point | 7.4. |
| Square set screw with collar and half dog point with rounded end | 7.5. |
| Triangle head bolt with collar | 8. |
| Octagon bolt | 9. |
| 12point flange screw | 10. |
| T-head bolt | 11.1. |
| T-head bolt with square neck | 11.2. |
| T-head bolt with double nib | 11.3. |
| Mushroom head square neck bolt | 12.1. |
| Cup head nib bolt | 12.2. |
| Mushroom head nib bolt | 12.3. |
| Cup oval neck bolt | 12.4. |
| Flat countersunk square neck bolt | 13.1. |
| Flat countersunk nib bolt | 13.2. |
| Deep flat countersunk bolt | 13.3. |
| Hexagon socket head cap screw | 14.1. |
| Hexagon socket head shoulder screw | 14.2. |
| Hexagon socket countersunk cap head screw | 14.3. |
| Slotted cheese head screw | 15.1. |
| Slotted pan head screw | 15.2. |
| Slotted raised cheese head screw | 15.3. |
| Slotted raised cheese head screw with full dog point | 15.4. |
| Slotted raised cheese head fit bolt | 15.5. |
| Slotted capstan screw | 15.6. |
| Slotted small raised cheese head screw | 15.7. |
| Slotted countersunk head screw | 15.8. |
| Slotted countersunk head screw with full dog point | 15.9. |
| Slotted raised countersunk head screw | 15.10. |
| Slotted raised countersunk head screw with full dog point | 15.11. |
| Countersunk head screw with forgel slot | 15.12. |
| Slotted round head screw | 15.13. |
| Cross recessed raised cheese head screw | 16.1. |
| Cross recessed countersunk head screw | 16.2. |
| Cross recessed raised countersunk head screw | 16.3. |
| Cross recessed pan head screw | 16.4. |
| Hexagon screw with captive plain washer | 17.1. |
| Hexagon screw with captive spring and plain washer | 17.2. |
| Raised cheese head screw with captive spring washer | 17.3. |
| Raised countersunk head screw with captive countersunk serrated lock washer | 17.4. |
| Eye bolt | 18.1. |
| Mushroom head anchor bolt | 18.2. |
| Flat head anchor bolt | 18.3. |
| Belting bolt | 18.4. |
| Clip bolt | 18.5. |
| Acorn hexagon head bolt | 18.6. |
| Conical bolt | 18.7. |
| Masonry bolt | 18.8. |
| Foundation bolt | 18.9. |
| Wing screw | 18.10. |
| Lifting eye bolt | 18.11. |
| Slotted set screw with flat point | 19.1. |
| Slotted set screw with full dog point | 19.2. |
| Slotted set screw with cup point | 19.3. |
| Slotted set screw with cone point | 19.4. |
| Hexagon socket set screw with flat point | 19.5. |
| Hexagon socket set screw with full dog point | 19.6. |
| Hexagon socket screw with cup point | 19.7. |
| Hexagon socket set screw with cone point | 19.8. |
| Hexagon head tapping screw | 20.1. |
| Slotted pan head tapping screw | 20.2. |
| Slotted countersunk head tapping screw | 20.3. |
| Slotted raised countersunk head tapping screw | 20.4. |
| Cross recessed countersunk head tapping screw | 20.5. |
| Cross recessed raised countersunk head tapping screw | 20.6. |
| Cross recessed pan head tapping screw | 20.7. |
| Hexagon head wood screw | 21.1. |
| Square head wood screw | 21.2. |
| Slotted round head wood screw | 21.3. |
| Slotted raised countersunk head wood screw | 21.4. |
| Slotted countersunk head wood screw | 21.5. |
| Cross recessed pan head wood screw | 21.6. |
| Cross recessed raised countersunk head wood screw | 21.7. |
| Cross recessed countersunk head wood screw | 21.8. |
| Hexagon head thread cutting screw | 22.1. |
| Slotted cheese head thread cutting screw | 22.2. |
| Slotted countersunk head thread cutting screw | 22.3. |
| Slotted raised countersunk head thread cutting screw | 22.4. |
| Cross recessed pan head thread cutting screw | 22.5. |
| Cross recessed countersunk head thread cutting screw | 22.6. |
| Cross recessed raised countersunk head thread cutting screw | 22.7. |
| Hexagon head thread forming screw | 23. |
| Straight knurled head screw | 24.1. |
| Straight knurled head screw with cone point | 24.2. |
| Straight knurled head screw with short dog point with truncated cone end | 24.3. |
| Straight knurled head screw with cup point | 24.4. |
| Straight knurled head screw with rounded point | 24.5. |
| Straight knurled head screw with full dog point | 24.6. |
| Cylindrical pin | 25.1. |
| Cylindrical pin with internal thread | 25.2. |
| Cylindrical pin with cup points | 25.3. |
| Cylindrical notched pin | 25.4. |
| Cylindrical notched pin with conical notches | 25.5. |
| Tension taper pin | 25.6. |
| Taper pin | 25.7. |
| Taper pin with internal thread | 25.8. |
| Taper pin with threaded stem | 25.9. |
| Spring type straight pin | 25.10. |
| Slotted headless screw with flat chamfered end | 25.11. |
| Hexagon socket headless screw with flat chamfered end | 25.12. |
| Hexagon socket headless screw with truncated cone point | 25.13. |
| Hexagon socket headless screw with full dog point | 25.14. |
| Hexagon socket headless screw with cup point | 25.15. |
| Stud | 26.1. |
| Waisted stud | 26.2. |
| Stud bolt | 26.3. |
| Weld stud | 26.4. |
| Double end stud with full shank | 26.5. |
| Round head rivet | 27.1. |
| Mushroom head rivet | 27.2. |
| Countersunk head rivet | 27.3. |
| Raised countersunk head rivet | 27.4. |
| Shallow raised countersunk head rivet | 27.5. |
| Flat head rivet | 27.6. |
| Round head hollow rivet | 27.7. |
| Flat head hollow rivet | 27.8. |
| Countersunk head hollow rivet | 27.9. |
| Flat head semi-hollow rivet | 27.10. |
| Countersunk head semi-hollow rivet | 27.11. |
| Round head semi-hollow rivet | 27.12. |
| Hexagon nut | 28.1. |
| Hexagon thin nut | 28.2. |
| Hexagon nut with collar | 28.3. |
| Hexagon nut with flange | 28.4. |
| Washer faced hexagon nut | 28.5. |
| Hexagon weld nut | 28.6. |
| Square nut | 28.7. |
| Square thin nut without chamfer | 28.8. |
| Foundation nut | 28.9. |
| Square nut with collar | 28.10. |
| Square weld nut | 28.11. |
| Triangle nut with collar | 28.12. |
| Octagon nut | 28.13. |
| 12point flange nut | 28.14. |
| Prevailing torque type hexagon nut with deformed thread | 28.15. |
| Prevailing torque type hexagon nut with ring polymer insert | 28.16. |
| Hexagon slotted nut | 28.17. |
| Hexagon castle nut | 28.18. |
| Hexagon thin castle nut | 28.19. |
| Acorn nut | 28.20. |
| Knurled nut | 28.21. |
| Slotted round nut | 28.22. |
| Slotted round nut for hook-spanner | 28.23. |
| Round nut with set pin holes in side | 28.24. |
| Round nut with drilled holes in one face | 28.25. |
| Wing nut | 28.26. |
| Plain washer | 29.1. |
| Square washer with round hole | 29.2. |
| Round washer with square hole | 29.3. |
| Square taper washer | 29.4. |
| Single coil spring lock washer with square ends | 29.5. |
| Single coil spring lock washer with tang ends | 29.6. |
| Double coil spring lock washer | 29.7. |
| Curvet spring washer | 29.8. |
| Serrated lock washer external teeth | 29.9. |
| Serrated lock washer internal teeth | 29.10. |
| Countersunk serrated external toothed lock washer | 29.11. |
| Wave spring washer | 29.12. |
| Lock washer external teeth | 29.13. |
| Lock washer internal teeth | 29.14. |
| Countersunk external toothed lock washer | 29.15. |
| Tab washer with long tab and wing | 29.16. |
| External tab washer | 29.17. |
| Tab washer with long tab | 29.18. |
| Internal tab washer | 29.19. |
| Split pin | 30. |
V. INDEX OF FASTENER TERMS AND NAMES IN FRENCH
| Filetage cylindrique | 1.1. |
|---|---|
| Filetage conique | 1.2. |
| Filetage de vis à tôle | 1.3. |
| Filetage de vis à bois | 1.4. |
| Filetage métrique (SI) | 1.5. |
| Filetage métrique à pas fin | 1.6. |
| Tête hexagonale | 2.1. |
| Tête hexagonale à collerette | 2.2. |
| Tête hexagonale à embase cylindrique | 2.3. |
| Tête hexagonale à embase cylindro-tronconique | 2.4. |
| Tête carrée | 2.5. |
| Tête carrée à embase cylindrique | 2.6. |
| Tête triangulaire à embase cylindrique | 2.7. |
| Têteoctogonale | 2.8. |
| Tête binexagonale | 2.9. |
| Tête rectangulaire à angles abattus | 2.10. |
| Tête rectangulaire à angles abattus à collet carré | 2.11. |
| Tête ronde | 2.12. |
| Tête bombée | 2.13. |
| Tête ronde à ergot | 2.14. |
| Tête bombée à collet carré | 2.15. |
| Tête ronde a collet carré large | 2.16. |
| Tête cylindrique | 2.17. |
| 2.19. Tête cylindrique bombée | 2.18. |
| Tête cylindrique à dépouille | 2.20. |
| Tête fraisée | 2.21. |
| Tête fraisée à épaulement | 2.22. |
| Tête fraisée à ergot | 2.23. |
| Tête fraisée à collet carré | 2.24. |
| Tête fraisée bombée | 2.25. |
| Tête fraisée bombée à épaulement | 2.26. |
| Tête cylindrique moletée | 2.27. |
| i>.Tête moletée croisé | 2.28. |
| Tige normale | 3.1. |
| Tige réduite | 3.2. |
| Tige ajustable | 3.3. |
| Tige allégeé | 3.4. |
| Tige ajustable à bout fileté réduit | 3.5. |
| Tige tubulaire | 3.6. |
| Tige demi-tubulaire | 3.7. |
| Bout plat | 4.1. |
| Bout bombé | 4.2. |
| Bout chanfreiné | 4.3. |
| Bout pointu | 4.4. |
| Bout pilote | 4.5. |
| Cuvette | 4.6. |
| Bout chanfreiné | 4.7. |
| Téton long | 4.8. |
| Téton court | 4.9. |
| Téton court bombé | 4.10. |
| Téton tronconique | 4.11. |
| Bout tronconique de vis à tôle | 4.12. |
| Bout pointu de vis à tôle | 4.13. |
| Bout plat de vis à tôle | 4.14. |
| Bout de vis auto-taraudeuse par déformation de matière | 4.15. |
| Foret | 4.16. |
| Hexagonal | 5.1. |
| Carré | 5.2. |
| Triangulaire | 5.3. |
| Oclogonal | 5.4. |
| Bihexagonal | 5.5. |
| Triangle creux | 5.6. |
| Carré creux | 5.7. |
| Six pans creux | 5.8. |
| Empreinte six cannelures | 5.9. |
| Empreinte bihexagonale | 5.10. |
| Fente | 5.11. |
| Empreinte cruciforme | 5.12. |
| Oreilles | 5.13. |
| Moleté | 5.14. |
| Moleté croisé | 5.15. |
| Percage en croix | 5.16. |
| Vis à tête hexagonale | 6.1. |
| Corps de boulon ajustable à tête hexagonale avec gorge de dégagement | 6.2. |
| Vis à tête hexagonale à téton avec gorge de digagement | 6.3. |
| Vis à tête hexagonale, à téton cylindro-tronconique | 6.4. |
| Vis à tete hexagonale à tige allégée | 6.5. |
| Vis à tête hexagonale à embase cylindrique | 6.6. |
| Vis à tête hexagonale à embase cylindlro-tronconique | 6.7. |
| Vis à tête carrée | 7.1. |
| Vis à tête carrée à embase cylindrique | 7.2. |
| Vis à tête carrée à teton court | 7.3. |
| Vis à tête carrée à cuvette | 7.4. |
| Vis à tête carrée à embase cylindrique à teton count | 7.5. |
| Vis à tête triangulaire à embase cylindrique | 8. |
| Vis à tête octogonale | 9. |
| Vis à tête bihexagonal | 10. |
| Vis à tête rectangulaire à angles abattus | 11.1. |
| Vis à tête rectangulaire à angles abattus à collet carré | 11.2. |
| Vis à tête rectangulaire à angles abattus à deux ergots | 11.3. |
| Corps de boulon à tête bombée aplatie, à collet carré | 12.1. |
| Corps de boulon à tête ronde, à ergot | 12.2. |
| Corps de boulon à tête bombee, à ergot | 12.3. |
| Corps de boulon à tête rondo, à collet carré large | 12.4. |
| Corps de boulon à tête fraisée, à collet carré | 13.1. |
| Corps de boulon à tête fraisee, à ergot | 13.2. |
| Corps de boulon de roue | 13.3. |
| Vis à tête cylindrique a six pans creux | 14.1. |
| Vis ajustable à tête cylindrique a six pans creux et à bout fileté réduite | 14.2. |
| Vis à tête fraisée à six pans creux | 14.3. |
| Vis à tête cylindrique fendue | 15.1. |
| Vis à tête cylindrique à depouille fendue | 15.2. |
| Vis à tête cylindrique bombée large fendue | 15.3. |
| Vis à tête cylindrique bombée mince fendue, à téton | 15.4. |
| Vis à tête cylindrique bombée mince fendue, à tige ajustable | 15.5. |
| Vis à tête cylindrique bombée fendue avec percage en croix | 15.6. |
| Vis à tête cylindrique bombée réduite fendue | 15.7. |
| Vis à tête fraisée fendue | 15.8. |
| Vis à tête fraisée fendue, à téton | 15.9. |
| Vis à tête fraisée bombée fendue | 15.10. |
| Vis à tête fraisée bombée fendue, à téton | 15.11. |
| Vis à tête fraisée à empreinte rectangulaife ou à fente forgée | 15.12. |
| Vis à tête ronde fendue | 15.13. |
| Vis à tête cylindrique bombée à empreinte cruciforme | 16.1. |
| Vis à tête fraisée à empreinte cruciforme | 16.2. |
| Vis à tête fraisée bombée à empreinte cruciforme | 16.3. |
| Vis à tête cylindrique à dépouille à empreinte cruciforme | 16.4. |
| Vis à tête hexagonale à rondelle cylindrique plate incorporée | 17.1. |
| Vis à tête hexagonale à rondelles (élastique et cylindrique plate) incorporées | 17.2. |
| Vis à tête cylindrique bombée, à rondelle élastique incorporée | 17.3. |
| Vis à tête fraisée bombée fendue, à rondelee à dents extérieures, concave, incorporée | 17.4. |
| Corps de boulon à oeil | 18.1. |
| Corps de boulon à tête bombée à agrafe (1 ou 2) | 18.2. |
| Corps de boulon à tête plate à agrafe (1 ou 2) | 18.3. |
| Corps de boulon de courroie | 18.4. |
| Crampon fileté | 18.5. |
| Vis à tête hexagonale à calotte | 18.6. |
| Vis conique | 18.7. |
| Tige de scellement à queue de carpe | 18.8. |
| Tige de scellement | 18.9. |
| Vis à oreilles | 18.10. |
| Vis à anneau | 18.11. |
| Vis sans tête, fendue, entiérement filetée, à bout chanfreiné | 19.1. |
| Vis sans tête, fendue, entiérement filetée, à téton | 19.2. |
| Vis sans tête, fendue, entiérement filetée, à cuvette | 19.3. |
| Vis sans tête, fendue, entiérement filetée, à bout pointu | 19.4. |
| Vis sans tête, à six pans creux, entierement filetée, à bout chanfreiné | 19.5. |
| Vis sans tête, à six pans creux, entierement filetée, à téton | 19.6. |
| Vis sans tête, à six pans crciix, entierement filelée, à cuvette | 19.7. |
| Vis sans tête, à six pans creux, entierement filutée, à bout pointu | 19.8. |
| Vis à tôle à tête hexagonale, à bout pointu; à bout plat | 20.1. |
| Vis à tôle à tête cylindrique à depouille fendue, à bout pointu; à bout plat | 20.2. |
| Vis à tôle à tête fraisée fendue, à bout pointu; à bout plat | 20.3. |
| Vis à tôle à tête fraisée bombée fendue, à bout pointu; à bout plat | 20.4. |
| Vis à tôle à tête fraisée à empreinte cruciforme, à bout pointu; à bout plat | 20.5. |
| Vis à tôle à tête fraisée bombée à empreinte cruciforme, à bout pointu; à bout plat | 20.6. |
| Vis à tôle à tête cylindrique à depouille à empreinte cruciforme, à bout pointu; à bout plat | 20.7. |
| Vis à bois à tête hexagonale | 21.1. |
| Vis à bois à tête carrée | 21.2. |
| Vis à bois à tête ronde fendue | 21.3. |
| Vis à bois à tête fraisée bombée fendue | 21.4. |
| Vis à bois à tête fraisée fendue | 21.5. |
| Vis à bois à tête ronde à empreinte cruciforme | 21.6. |
| Vis à bois à tête fraisée bombée à empreinte cruciforme | 21.7. |
| Vis à bois à tête fraisée à empreinte cruciforme | 21.8. |
| Vis auto-taraudeuse à tête hexagonale | 22.1. |
| Vis auto-taraudeuse à tête cylindrique fendue | 22.2. |
| Vis auto-taraudeuse à tête fraisfée fendue | 22.3. |
| Vis auto-taraudeuse à tête fraisée bombée fendue | 22.4. |
| Vis auto-taraudeuse à tête cylindrique à dépouille à empreinte cruciforme | 22.5. |
| Vis auto-taraudeuse à tête fraisée à empreinte cruciforme | 22.6. |
| Vis auto-taraudeuse à tête fraisée bombée à empreinte cruciforme | 22.7. |
| Vis auto-taraudeus par deformation de matiére | 23. |
| Vis à tête cylindrique moletée | 24.1. |
| Vis à tête cylindrique moletée, à bout pointu | 24.2. |
| Vis à tête cylindrique moletée à téton cylindro-tronconique | 24.3. |
| Vis à tête cylindrique moletée à cuvette | 24.4. |
| Vis à tête cylindrique moletée à bout bombée | 24.5. |
| Vis à tête cylindrique moletée à téton long | 24.6. |
| Goupille cylindrique | 25.1. |
| Goupille cylindrique à filet femelle | 25.2. |
| Goupille cylindrique à cuvette | 25.3. |
| Goupille cylindrique à taille | 25.4. |
| Goupille cylindrique à tailles coniques | 25.5. |
| Goupille conique fendue | 25.6. |
| Goupille cunique | 25.7. |
| Goupille conique à filet femelle | 25.8. |
| Goupille conique à tourillon fileté | 25.9. |
| Goupille elastique | 25.10. |
| Vis sans tête fendue, partiellement filetée, à bout chanfreiné | 25.11. |
| Vis sans tête à six pans creux, partiellement, filetée, à bout chanfreiné | 25.12. |
| Vis sans tête à six pans creux, partiellement filetée, à bout pointu | 25.13. |
| Vis sans tête à six pans creux, partiellement filetée, à téton | 25.14. |
| Vis sans tête à six pans creux, partiellement filetée, à cuvette | 25.15. |
| Goujon | 26.1. |
| Goujon à corps allégé | 26.2. |
| Tige filetée | 26.3. |
| Tige à sounde | 26.4. |
| Goujon à deux gorges de dégagement et à téton | 26.5. |
| Rivet à tête ronde | 27.1. |
| Rivet à tête bombée | 27.2. |
| Rivet à tête fraisée | 27.3. |
| Rivet à tête fraisée bombée | 27.4. |
| Rivet à tête fraisée bombée bas | 27.5. |
| Rivet à tête plate | 27.6. |
| Rivet cretix à tête ronde | 27.7. |
| Rivet creux à tête plate | 27.8. |
| Rivet creux à tête fraisée | 27.9. |
| Rivet semi-creux à tête plate | 27.10. |
| Rivet semi-crcux à tête fraisée | 27.11. |
| Rivet semi-creux à tête ronde | 27.12. |
| Ecrou hexagonal | 28.1. |
| Ecrou hexagonal bas | 28.2. |
| Ecrou hexagonal à embase cylindrique | 28.3. |
| Ecrou hexagonal à embase cylindro-tronconique | 28.4. |
| Ecrou hexagonal à collerette | 28.5. |
| Ecrou hexagonal à souder | 28.6. |
| Ecrou carré | 28.7. |
| Ecrou carre bas | 28.8. |
| Ecrou de tige d’ancrage | 28.9. |
| Ecrou carré à embase cylindrique | 28.10. |
| Ecrou carré à souder | 28.11. |
| Ecrou triangulaire à embase cylindrique | 28.12. |
| Ecrou octogonal | 28.13. |
| Ecrou bihexagonal | 28.14. |
| Ecrou auto-freiné hexagonal à filet déformé | 28.15. |
| Ecrou auto-freiné hexagonal anneau polimére | 28.16. |
| Ecrou hexagonal à créneaux | 28.17. |
| Ecrou hexagonal à créneaux dégagés | 28.18. |
| Ecrou hexagonal bas à creneaux dégagés | 28.19. |
| Ecrou borgne à calotte | 28.20. |
| Ecrou moleté | 28.21. |
| 28.23. Ecrou cylindrique à fente | 28.22. |
| Ecrou cylindrique à trous percés en croix | 28.24. |
| Ecrou cylindrique à deux trous percés sur une fase | 28.25. |
| Ecrou à oreilles | 28.26. |
| Rondelle plats | 29.1. |
| Plaquette carrée | 29.2. |
| Rondelle plate à trou carrée | 29.3. |
| Plaquette oblique | 29.4. |
| Rondelle élastique simple spire sans becs | 29.5. |
| Rondelle élastique simple spire abes becs | 29.6. |
| Rondelle élastique double spire sans becs | 29.7. |
| Rondelle élastique cintrée | 29.8. |
| Rondelle élastique plane à dents chevauchantes extérieures | 29.9. |
| Rondelle élastique plane à dents chevauchantes intérieures | 29.10. |
| Rondelle élastique concave à dents chevauchantes extérieures | 29.11. |
| Rondelle élastique ondulée | 29.12. |
| Rondelle élastique plane à dents espacées extérieures | 29.13. |
| Rondelle élastique plane à dents espacées intérieures | 29.14. |
| Rondelle élasllque concave à dents espacées extérieures | 29.15. |
| Frein d’ecrou d’equerre à aileron | 29.16. |
| Rondelle frein d’ecrou à ergot extérieur | 29.17. |
| Frein d’ecrou droit à aileron | 29.18. |
| Rondelle frein d’ecrou à ergot intérieur | 29.19. |
| Goupille cylirndrique fendue | 30. |
INFORMATIONAL DATA
- DEVELOPED AND SUBMITTED BY the Ministry of Ferrous Metallurgy of the USSR
DEVELOPERS
B.M. Rigmant; T.E. Yurchenko
-
APPROVED AND PUT INTO EFFECT by Resolution of the USSR State Committee for Standards dated 30.09.86 No. 2941
-
Review date: 2000, review interval: 10 years
-
The standard fully complies with ST SEV 6300-88
-
The standard fully complies with international standard ISO 1891-79
-
INTRODUCED FOR THE FIRST TIME
-
REFERENCE REGULATORY AND TECHNICAL DOCUMENTS
| Designation of the referenced regulatory document | Clause number |
|---|---|
| GOST 11708-82 | Introductory part |
- REISSUED March 1990 with Amendment No. 1, approved in June 1989 (IUS 11-89)
Request
Estimate for the “GOST 27017-86” category
Send a specification or specify volumes — we will prepare a commercial proposal with timelines and payment terms within one business day.
Moscow +7 (495) 120-56-20 St Petersburg +7 (812) 270-75-80 zakaz@flok-stroy.ru Mon–Fri · 10:00–18:00