GOST 22036-76 Studs with Threaded End of 1.6d, Product Grade B

Studs with threaded end of 1.6d. Product grade B. Construction and dimensions.

GOST 22036-76

Studs with Threaded End of 1.6d. Product Grade B. Construction and Dimensions.	GOST 22036-76* Supersedes GOST 11765-66 with regard to the length of the threaded end l₁=1.6d

By Resolution No. 1934 of the USSR State Committee for Standards of the Council of Ministers dated August 13, 1976, the effective date was set at 01.07.78.

Reviewed in 1983. By Resolution of Gosstandart No. 1760 dated 14.04.83, the validity period was extended to 01.01.89.

Reissue (June 1987) with Amendments No. 1, 2, 3, approved in December 1978, June 1980, April 1983; Resolution No. 1758 dated 14.04.83 (IUS 2-79, 8-80, 7-83).

Amendment No. 4 was approved and put into effect by Resolution No. 1204 of the USSR State Committee for Standards dated 28.04.88. Effective date 01.01.89.

1. This standard applies to studs with a nominal thread diameter from 2 to 48 mm, manufactured:

• with coarse pitch thread on the nut end and the threaded end;
• with fine pitch thread on the nut end and the threaded end;
• with fine pitch thread on the threaded end and coarse pitch thread on the nut end;
• with coarse pitch thread on the threaded end and fine pitch thread on the nut end.

2. The construction and dimensions of studs shall conform to those shown in the drawing and in Tables 1, 2.

Type 1

Type 2

d₂ is approximately equal to the pitch diameter of the thread.

Table 1, mm

Nominal thread diameter d	2	2.5	3	4	5	6	8	10	12	(14)	16	(18)	20	(22)	24	(27)	30	36	42	48
Pitch P:
coarse	0.4	0.45	0.5	0.7	0.8	1	1.25	1.5	1.75	2		2.5			3		3.5	4	4.5	5
fine	-	-	-	-	-	-	1	1.25		1.5					2			3
Shank diameter d₁	2	2.5	3	4	5	6	8	10	12	14	16	18	20	22	24	27	30	36	42	48
Length of threaded end b₁	3.2	4	5	6.5	8	10	14	16	20	22	25	28	32	35	38	42	48	56	68	76

Note. Dimensions in parentheses are not recommended for use.

Table 2, mm

Stud length l	Length of nut-end thread b at nominal thread diameter d
	2	2.5	3	4	5	6	8	10	12	(14)	16	(18)	20	(22)	24	(27)	30	36	42	48
10	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
12	10	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
14	10	11	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
16	10	11	12	×	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-
(18)	10	11	12	14	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-
20	10	11	12	14	16	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-
(22)	10	11	12	14	16	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-
25	10	11	12	14	16	18	×	×	×	×	-	-	-	-	-	-	-	-	-	-
(28)	10	11	12	14	16	18	22	×	×	×	-	-	-	-	-	-	-	-	-	-
30	10	11	12	14	16	18	22	×	×	×	-	-	-	-	-	-	-	-	-	-
(32)	10	11	12	14	16	18	22	×	×	×	-	-	-	-	-	-	-	-	-	-
35	10	11	12	14	16	18	22	26	×	×	×	×	-	-	-	-	-	-	-	-
(38)	10	11	12	14	16	18	22	26	30	×	×	×	-	-	-	-	-	-	-	-
40	10	11	12	14	16	18	22	26	30	×	×	×	×	-	-	-	-	-	-	-
(42)	10	11	12	14	16	18	22	26	30	×	×	×	×	-	-	-	-	-	-	-
45	10	11	12	14	16	18	22	26	30	34	×	×	×	×	×	-	-	-	-	-
(48)	10	11	12	14	16	18	22	26	30	34	38	×	×	×	×	-	-	-	-	-
50	10	11	12	14	16	18	22	26	30	34	38	×	×	×	×	-	-	-	-	-
55	10	11	12	14	16	18	22	26	30	34	38	42	×	×	×	×	-	-	-	-
60	10	11	12	14	16	18	22	26	30	34	38	42	46	×	×	×	×	-	-	-
65	10	11	12	11	16	18	22	26	30	34	38	42	46	50	×	×	×	-	-	-
70	10	11	12	14	16	18	22	26	30	34	38	42	46	50	54	×	×	×	-	-
75	10	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	×	×	-	-
80	10	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	×	×	×	×
85	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	×	×	×
90	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	×	×	×
(95)	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	78	×	×
100	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	78	×	×
(105)	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	78	×	×
110	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	78	90	×
(115)	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	78	90	×
120	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	78	90	×
130	-	17	18	20	22	24	28	32	36	40	44	48	52	56	60	66	72	84	96	108
140	-	17	18	20	22	24	28	32	36	40	44	48	52	56	60	66	72	84	96	108
150	-	17	18	20	22	24	28	32	36	40	44	48	52	56	60	66	72	81	96	108
160	-	17	18	20	22	24	28	32	36	40	44	48	52	56	60	66	72	84	96	108
170	-	-	-	-	-	-	28	32	36	40	44	48	52	56	60	66	72	84	96	108
180	-	-	-	-	-	-	28	32	36	40	44	48	52	56	60	66	72	84	96	108
190	-	-	-	-	-	-	28	32	36	40	44	48	52	56	60	66	72	84	96	108
200	-	-	-	-	-	-	28	32	36	40	44	48	52	56	60	66	72	84	96	108
220	-	-	-	-	-	-	-	-	49	53	57	61	65	69	73	79	85	97	109	121
240	-	-	-	-	-	-	-	-	-	-	-	-	65	69	73	79	85	97	109	121
260	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	79	85	97	109	121
280	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	97	109	121
300	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	97	109	121

Notes:

1. Dimensions in parentheses are not recommended for use.
2. Studs with nut-end length b=l-0.5d-2P are marked with ×.

Example of designation for a design 1 stud with thread diameter d=16 mm, coarse pitch P=2 mm with tolerance class 6g, length l=120 mm, property class 5.8, without coating:

Stud M16 - 6g×120.58 GOST 22036-76

The same, design 2 with fine pitch P=1.5 mm, tolerance class 6g, property class 10.9, made of steel grade 40Kh, with coating 02, thickness 6 µm:

Stud 2 M16×1.5-6g×120.109.40Kh.026 GOST 22036-76

Same, with fine pitch P=1.5 mm, tolerance class 2r on the threaded end, coarse pitch P=2 mm, tolerance class 6g on the nut end, property class 6.6, with coating 05:

Stud M16××120.66.05 GOST 22036-76

3. Thread - as per GOST 24705-81.

3a. Thread runout dimensions - as per GOST 27148-86.

3b. Dimensional tolerances, form and position deviations of surfaces, inspection methods - as per GOST 1759.1-82.

3c. Surface defects and inspection methods for studs - as per GOST 1759.2-82.

4. The surface of the smooth shank portion d₁ is not machined when studs are made from calibrated bar stock.

6. By agreement between the manufacturer and the customer, an interference-fit thread as per GOST 4608-81 may be made on the threaded end of the stud, with this indicated in the stud’s designation; such studs shall be marked by center-punching (1 punch mark) on the end face of the nut end.

7. Technical requirements - as per GOST 1759.0-87.

8. The theoretical mass of studs is given in reference Appendices 1 and 2.

APPENDIX 1 (informative)

Stud length l, mm	Theoretical mass of 1000 pcs of steel Type 1 studs, kg, with coarse pitch thread, at nominal thread diameter d, mm
	2	2.5	3	4	5	6	8	10	12	(14)	16	(18)	20	(22)	24	(27)	30	36	42	48
10	0.258	0.438	0.685	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
12	0.308	0.511	0.795	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
14	0.344	0.571	0.873	1.653	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
16	0.393	0.641	0.972	1.828	3.095	4.773	9.862	16.53	-	-	-	-	-	-	-	-	-	-	-	-
(18)	0.443	0.721	1.083	1.983	3.342	5.126	10.490	17.54	-	-	-	-	-	-	-	-	-	-	-	-
20	0.495	0.801	1.194	2.181	3.590	5.479	11.140	18.54	-	-	-	-	-	-	-	-	-	-	-	-
(22)	0.545	0.880	1.310	2.378	3.890	5.919	11.930	19.77	-	-	-	-	-	-	-	-	-	-	-	-
25	0.615	0.991	1.470	2.669	4.260	6.492	12.960	21.40	33.87	48.24	-	-	-	-	-	-	-	-	-	-
(28)	0.685	1.111	1.640	2.969	4.770	7.142	13.990	23.02	36.20	51.43	-	-	-	-	-	-	-	-	-	-
30	0.735	1.191	1.750	3.169	5.170	7.642	14.630	24.02	37.00	53.41	-	-	-	-	-	-	-	-	-	-
(32)	0.785	1.260	1.860	3.369	5.470	8.042	15.470	25.03	39.11	55.40			-	-	-	-	-	-	-	-
35	0.865	1.371	2.030	3.659	5.870	8.742	16.570	26.65	41.46	58.60	82.15	107.3	-	-	-	-	-	-	-	-
(38)	0.935	1.491	2.190	3.959	6.370	9.342	17.770	28.50	43.82	61.82	86.41	112.6	-	-	-	-	-	-	-	-
40	0.985	1.571	2.300	4.149	6.670	9.842	18.570	29.70	45.28	63.81	89.10	115.9	153.8	-	-	-	-	-	-	-
(42)	1.035	1.690	2.420	4.349	6.970	10.240	19.370	31.00	47.08	65.80	91.74	119.2	157.9	-	-	-	-	-	-	-
45	1.105	1.781	2.580	4.649	7.470	10.940	20.570	32.80	49.69	68.99	96.01	124.5	164.5	208.3	255.0	-	-	-	-	-
(48)	1.185	1.921	2.750	4.939	7.870	11.640	21.770	34.70	52.38	72.59	99.73	129.1	166.2	216.7	263.3	-	-	-	-	-
50	1.235	2.001	2.860	5.139	8.170	12.040	22.570	35.90	54.18	74.99	102.80	133.1	171.2	222.7	270.4	-	-	-	-	-
55	1.355	2.101	3.140	5.629	8.970	13.140	24.470	39.00	.58.58	81.09	110.70	141.7	186.2	235.8	286.0	383.4	-	-	-	-
60	1.485	2.301	3.410	6.129	9.770	14.240	26.470	42.10	62.98	87.09	118.60	151.7	196.9	249.1	301.5	403.4	523.2	-	-	-
65	1.605	2.501	3.690	6.619	10.470	15.340	28.470	45.20	67.49	93.09	126.50	161.7	209.3	262.4	317.1	423.4	547.7	-	-	-
70	1.725	2.701	3.970	7.109	11.270	16.440	30.470	48.20	71.88	99.19	134.40	171.6	221.6	277.3	332.6	443.4	572.2	884.5	-	-
75	1.855	2.901	4.250	7.599	12.070	17.640	32.370	51.30	76.38	105.20	142.30	181.6	233.9	292.2	350.4	462.1	595.8	917.8	-	-
80	1.975	3.101	4.520	8.099	12.870	18.740	34.370	54.40	80.78	111.30	150.20	191.6	246.2	307.1	368.1	484.6	623.6	957.7	1423	1963
85	-	3.301	4.800	8.589	13.570	19.840	36.370	57.50	85.18	117.30	158.10	201.6	258.6	322.0	385.9	507.1	645.7	991.0	1468	2023
90	-	3.501	5.080	9.079	14.370	20.910	38.370	60.60	89.98	123.30	166.00	211.6	270.9	337.0	403.6	529.6	673.5	1024.0	1514	2083
(95)		3.701	5.360	9.579	15.17	22.04	40.27	63.70	94.08	129.4	173.8	221.6	283.2	351.9	421.4	552.0	701.2	1061	1564	2149
100	-	3.901	5.630	10.070	15.87	23.14	42.27	66.80	98.58	135.4	181.7	231.6	295.6	366.8	439.1	574.5	729.0	1098	1611	2210
(105)	-	4.101	5.910	10.560	16.67	24.24	44.27	69.80	103.00	141.5	189.6	241.6	397.9	381.7	456.9	597.0	753.7	1137	1658	2272
110	-	4.301	6.190	11.060	17.47	25.34	46.27	72.90	108.00	147.5	197.5	251.6	321.2	396.6	474.7	619.5	784.5	1177	1705	2334
(115)	-	4.501	6.517	11.590	18.17	26.44	48.17	76.00	111.90	153.5	205.4	261.6	332.6	411.6	492.4	641.9	812.2	1217	1759	2405
120	-	4.701	6.791	12.080	18.59	27.34	50.17	79.10	116.30	159.6	213.3	271.5	344.9	426.5	510.2	664.4	839.9	1257	1814	2458
130		5.091	7.350	13.070	20.17	29.64	54.63	85.57	125.40	171.7	229.1	291.5	369.5	456.3	545.7	709.4	895.4	1337	1923	2596
140	-	5.471	7.900	14.050	21.67	30.84	58.57	91.70	134.40	183.9	245.5	311.5	494.2	486.2	581.2	754.3	950.9	1417	2031	2738
150	-	5.091	8.460	15.040	23.17	34.04	62.47	97.90	143.40	196.0	260.8	331.7	419.3	515.6	616.7	799.3	1006.0	1497	2140	2880
160	-	6.201	9.010	16.030	24.77	36.24	66.47	103.40	151.00	206.9	275.1	349.7	442.2	542.9	648.8	840.4	1057.0	1570	2241	3011
170	-	-	-	-	-	-	70.47	109.50	159.90	218.9	290.9	369.7	467.3	572.7	684.3	885.8	1113.0	1659	2350	3153
180	-	-	-	-	-	-	74.37	115.70	168.80	231.0	306.7	389.6	490.9	602.6	719.7	930.8	1168.0	1730	2458	3295
190	-	-	-	-	-	-	78.37	121.90	177.70	243.1	322.5	409.6	515.6	632.4	755.3	975.8	1224.0	1810	2567	3437
200	-	-	-	-	-	-	82.27	123.10	186.50	255.2	338.3	429.6	540.3	662.2	790.8	1021.0	1279.0	1890	2676	3579
220		-	-	-	-	-	-	-	204.30	279.3	369.8	449.6	589.6	721.9	861.9	1111.0	1390.0	2050	2895	3863
240	-	-	-	-	-	-	-	-	-	-	-	-	638.9	781.6	932.9	1200.0	1501.0	2209	3111	4148
260	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	1290.0	1612.0	2369	3329	4432
280	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	2529	3546	4716
300	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	2689	3763	5000

Note. To determine the mass of studs made from other materials, the mass values given in the table shall be multiplied by the coefficient: 0.356 for aluminium alloy; 0.970 for bronze; 1.080 for brass.

APPENDIX 2 (informative)

Stud length l, mm	Theoretical mass of 1000 pcs of steel Type 2 studs, kg, with coarse pitch thread, at nominal thread diameter d, mm
	2	2.5	3	4	5	6	8	10	12	(14)	16	(18)	20	(22)	24	(27)	30	36	42	48
10	0.216	0.421	0.661	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
12	0.284	0.481	0.750	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
14	0.321	0.541	0.794	1.588	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
16	0.358	0.601	0.926	1.742	2.968	4.586	9.552	16.065	-	-	-	-	-	-	-	-	-	-	-	-
(18)	0.396	0.661	1.014	1.897	3.216	4.939	10.188	17.069	-	-	-	-	-	-	-	-	-	-	-	-
20	0.433	0.721	1.102	2.052	3.463	5.291	10.825	18.073	-	-	-	-	-	-	-	-	-	-	-	-
(22)	0.470	0.781	1.191	2.207	3.710	5.644	11.462	19.077	-	-	-	-	-	-	-	-	-	-	-	-
25	0.526	0.871	1.323	2.439	4.081	6.173	12.417	20.583	32.72	46.72	-	-	-	-	-	-	-	-	-	-
(28)	0.582	0.961	1.455	2.672	4.452	6.702	13.372	22.089	34.90	49.70	-	-	-	-	-	-	-	-	-	-
30	0.619	1.021	1.543	2.827	4.700	7.055	14.009	23.093	36.36	51.69	-	-	-	-	-	-	-	-	-	-
(32)	0.657	1.082	1.632	2.982	4.947	7.408	14.646	24.097	37.81	53.68	-	-	-	-	-	-	-		-	-
35	0.713	1.172	1.764	3.214	5.318	7.937	15.601	25.604	40.00	56.66	79.91	104.1	-	-	-	-	-	-	-	-
(38)	0.769	1.262	1.896	3.446	5.689	8.466	16.556	27.110	42.18	59.64	83.90	109.1	-	-	-	-	-	-	-	-
40	0.806	1.322	1.984	3.601	5.937	8.819	17.193	28.114	43.63	61.63	86.57	112.4	149.8	-	-	-	-	-	-	-
(42)	0.843	1.382	2.073	3.756	6.184	9.172	17.830	29.118	45.09	63.62	89.23	115.7	154.0	-	-	-	-	-	-	-
45	0.899	1.472	2.205	3.988	6.555	9.701	18.785	30.624	47.27	66.60	93.23	120.6	160.2	204.7	248.7	-	-	-	-	-
(48)	0.955	1.562	2.337	4.221	6.926	10.230	19.740	32.130	49.45	69.59	97.22	125.6	166.5	212.4	257.7	-	-	-	-	-
50	0.993	1.662	2.425	4.375	7.173	10.583	20.377	33.134	50.90	71.57	99.88	128.9	170.6	217.5	263.7	-	-	-	-	-
55	1.086	1.773	2.646	4.763	7.792	11.465	21.969	35.644	54.54	76.54	106.54	137.2	181.0	230.3	278.7	375.1	-	-	-	-
60	1.179	1.923	2.866	5.150	8.410	12.347	23.561	38.154	58.17	81.51	113.20	145.4	191.4	243.1	293.6	394.5	511.7	-	-	-
65	1.272	2.073	3.087	5.537	9.029	13.228	25.153	40.664	61.81	86.48	119.86	153.7	201.8	255.9	308.6	413.8	535.3	-	-	-
70	1.366	2.223	3.307	5.924	9.647	14.110	26.745	43.175	65.45	91.45	126.52	162.0	212.3	268.6	323.6	433.1	559.0	866.3	-	-
75	1.459	2.373	3.528	6.312	10.265	14.992	28.336	45.685	69.08	96.42	133.18	170.2	222.7	281.4	338.6	452.5	582.7	900.7	-	-
80	1.552	2.524	3.748	6.699	10.884	15.874	29.928	48.195	72.72	101.39	139.84	178.5	233.1	294.2	353.6	471.8	606.4	935.0	1393	1925
85	-	2.674	3.969	7.086	11.502	16.756	31.520	50.705	76.35	106.37	146.50	186.7	243.5	307.0	368.6	491.1	630.1	969.4	1440	1987
90	-	2.824	4.189	7.473	12.121	17.638	33.112	53.215	79.99	111.34	153.15	195.0	253.9	319.8	383.5	510.5	653.8	1003.8	1487	2049
(95)	-	2.974	4.410	7.860	12.739	18.520	34.704	55.725	83.63	116.31	159.81	203.3	264.3	332.6	398.5	529.8	677.5	1038.2	1534	2110
100	-	3.124	4.630	8.248	13.357	19.402	36.296	58.236	87.26	121.28	166.47	211.5	274.7	345.4	413.5	549.1	701.1	1072.5	1581	2172
(105)	-	3.275	4.850	8.635	13.976	20.284	37.888	60.746	90.90	126.25	173.13	219.8	285.1	358.2	428.5	568.5	724.8	1106.9	1628	2231
110	-	3.425	5.071	9.022	14.594	21.165	39.480	63.256	94.53	131.22	179.79	228.1	295.5	371.0	443.5	587.8	748.5	1141.3	1675	2296
(115)	-	3.575	5.291	9.409	15.212	22.047	41.072	65.766	98.17	136.19	186.45	236.3	305.9	383.8	458.5	607.1	772.2	1175.7	2098	2357
120	-	3.725	5.512	9.796	15.831	22.929	42.664	68.276	101.80	141.16	193.11	244.6	316.3	396.6	473.4	626.5	795.9	1210.0	1769	2419
135	-	4.026	5.953	10.571	17.068	24.693	45.848	73.296	109.08	151.10	206.43	261.1	337.1	422.1	503.4	665.2	843.3	1278.8	1863	2542
140	-	4.326	6.394	11.345	18.305	26.457	49.032	78.317	116.35	161.04	219.74	277.6	357.9	447.7	533.4	703.8	890.6	1347.5	1957	2666
150	-	4.627	6.835	12.120	19.541	28.221	52.215	83.337	123.62	170.98	233.06	294.2	378.7	473.3	563.3	742.5	938.0	1416.3	2051	2789
160	-	4.927	7.276	12.894	20.778	29.984	55.399	88.357	130.89	180.92	246.38	310.7	399.5	498.9	593.3	781.2	985.4	1485.0	2145	2913
170	-	-	-	-	-	-	58.583	93.378	138.16	190.86	259.70	327.2	420.3	524.5	623.3	819.8	1032.8	1553.8	2240	3036
180	-	-	-	-	-	-	61.767	98.398	145.43	200.80	273.02	343.7	441.1	550.1	653.2	858.5	1080.1	1622.5	2334	3159
190	-	-	-	-	-	-	64.951	103.420	152.71	210.74	286.33	360.3	462.0	575.7	683.2	897.2	1127.5	1691.3	2428	3283
200	-	-	-	-	-	-	68.135	108.440	159.98	220.68	299.65	376.8	482.8	601.2	713.1	935.9	1174.9	1760.0	2522	3406
220	-	-	-	-	-	-	-	-	174.52	240.56	326.29	408.8	524.4	652.4	773.1	1013.2	1269.6	1897.6	2710	3653
240	-	-	-	-	-	-	-	-	-	-	-	-	566.0	703.6	833.0	1090.5	1364.4	2035.1	2898	3900
260	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	1167.9	1459.1	2172.6	3086	4147
280	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	2310.1	3275	4394
300	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	2447.6	3463	4640

Note. To determine the mass of studs made from other materials, the mass values given in the table shall be multiplied by the coefficient: 0.356 for aluminium alloy; 0.970 for bronze; 1.080 for brass.