GOST 22033-76 Studs with Threaded End of 1d, Product Grade A

Studs with Threaded End of 1d

Product grade A

Design and dimensions

GOST 22033-76

(ST SEV 5954-87)

State Committee of the USSR for Standards

Moscow

State Standard of the Union of Soviet Socialist Republics

STUDS WITH THREADED END OF 1d. Product grade A. Construction and dimensions Studs with threaded end of 1d. Product grade A. Construction and dimensions	GOST 22033-76* (ST SEV 5954-87) Supersedes GOST 11766-66 regarding the length of the threaded end l₁=d

By Resolution of the State Committee for Standards of the Council of Ministers of the USSR dated August 13, 1976 No. 1934, the effective date was established

from 01.07.78

Reviewed in 1983. By Resolution of Gosstandart dated 14.04.83 No. 1760, the validity period was extended

until 01.01.89

• Reissue (June 1987) with Amendments No. 1, 2, 3,

approved in December 1978, June 1980, April 1983;

Resolution No. 1758 dated 14.04.83 (IUS 2-79, 8-80, 7-83)

Amendment No. 4 to GOST 22033-76 Studs with threaded end of 1d. Product grade A. Construction and dimensions

Approved and put into effect by Decree No. 1205 of the USSR State Committee for Standards dated 28.04.88

Effective date 01.01.89

Non-compliance with the standard is punishable by law

1. This standard applies to studs with a nominal thread diameter from 2 to 48 mm, manufactured with coarse thread pitch on both the nut end and the threaded end; with fine thread pitch on both the nut end and the threaded end; with fine thread pitch on the threaded end and coarse thread pitch on the nut end; with coarse thread pitch on the threaded end and fine thread pitch on the nut end.

2. The design and dimensions of studs shall conform to those shown in the drawing and in Tables 1, 2.

Type 1

Type 2

d₂ is approximately equal to the pitch diameter of the thread

Note. (Deleted, Amendment No. 4)

Table 1

mm

Nominal thread diameter d	2	2.5	3	4	5	6	8	10	12	(14)	16	(18)	20	(22)	24	(27)	30	(33)	36	(39)	42	(45)	48
Pitch P:
coarse	0.4	0.45	0.5	0.7	0.8	1	1.25	1.5	1.75	2			2.5		3		3.5		4		4.5		5
fine	-	-	-	-	-	-	1	1.25		1.5					2				3
Shank diameter d₁	2	2.5	3	4	5	6	8	10	12	14	16	18	20	22	24	27	30	33	36	39	42	45	48
Length of threaded end b₁	3			4	5	6	8	10	12	14	16	18	20	22	24	27	30	33	36	39	42	45	48

Note. Dimensions in parentheses are not recommended for use.

(Amended edition, Amendment No. 4)

Table 2

mm

Stud length l	Length of nut-end thread b at nominal thread diameter d
	2	2.5	3	4	5	6	8	10	12	(14)	16	(18)	20	(22)	24	(27)	30	(33)	36	(39)	42	(45)	48
10	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
12	10	×	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
14	10	11	×	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
16	10	11	×	×	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
(18)	10	11	12	14	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
20	10	11	12	14	16	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
(22)	10	11	12	14	16	×	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-	-
25	10	11	12	14	16	18	×	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-	-
(28)	10	11	12	14	16	18	22	×	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-
30	10	11	12	14	16	18	22	×	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-
(32)	10	11	12	14	16	18	22	×	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-
35	10	11	12	14	16	18	22	26	×	×	×	×	-	-	-	-	-	-	-	-	-	-	-
(38)	10	11	12	14	16	18	22	26	30	×	×	×	-	-	-	-	-	-	-	-	-	-	-
40	10	11	12	14	16	18	22	26	30	×	×	×	×	-	-	-	-	-	-	-	-	-	-
(42)	10	11	12	14	16	18	22	26	30	×	×	×	×	-	-	-	-	-	-	-	-	-	-
45	10	11	12	14	16	18	22	26	30	34	×	×	×	×	×	-	-	-	-	-	-	-	-
(48)	10	11	12	14	16	18	22	26	30	34	38	×	×	×	×	-	-	-	-	-	-	-	-
50	10	11	12	14	16	18	22	26	30	34	38	×	×	×	×	-	-	-	-	-	-	-	-
55	10	11	12	14	16	18	22	26	30	34	38	42	×	×	×	×	-	-	-	-	-	-	-
60	10	11	12	14	16	18	22	26	30	34	38	42	46	×	×	×	×	-	-	-	-	-	-
65	10	11	12	14	16	18	22	26	30	34	38	42	46	50	×	×	×	-	-	-	-	-	-
70	10	11	12	14	16	18	22	26	30	34	38	42	46	50	54	×	×	×	×	-	-	-	-
75	10	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	×	×	×	-	-	-	-
80	10	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	×	×	×	×	×	×	×
85	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	72	×	×	×	×	×
90	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	72	×	×	×	×	×
(95)	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	72	78	84	×	×	×
100	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	72	78	84	×	×	×
(105)	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	72	78	84	×	×	×
110	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	72	78	84	90	96	×
(115)	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	72	78	84	90	96	102
120	-	11	12	14	16	18	22	26	30	34	38	42	46	50	54	60	66	72	78	84	90	96	102
130	-	17	18	20	22	24	28	32	36	40	44	48	52	56	60	66	72	78	84	90	96	102	108
140	-	17	18	20	22	24	28	32	36	40	44	48	52	56	60	66	72	78	84	90	96	102	108
150	-	17	18	20	22	24	28	32	36	40	44	48	52	56	60	66	72	78	81	90	96	102	108
160	-	17	18	20	22	24	28	32	36	40	44	48	52	56	60	66	72	78	84	90	96	102	108
170	-	-	-	-	-	-	28	32	36	40	44	48	52	56	60	66	72	78	84	90	96	102	108
180	-	-	-	-	-	-	28	32	36	40	44	48	52	56	60	66	72	78	84	90	96	102	108
190	-	-	-	-	-	-	28	32	36	40	44	48	52	56	60	66	72	78	84	90	96	102	108
200	-	-	-	-	-	-	28	32	36	40	44	48	52	56	60	66	72	78	84	90	96	102	108
220	-	-	-	-	-	-	-	-	49	53	57	61	65	69	73	79	85	91	97	103	109	115	121
240	-	-	-	-	-	-	-	-	-	-	-	-	65	69	73	79	85	91	97	103	109	115	121
260	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	79	85	91	97	103	109	115	121
280	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	79	85	91	97	103	109	115	121
300	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	85	91	97	103	109	115	121

Notes:

1. Dimensions in parentheses are not recommended for use.

2. Studs with nut-end length b=l-0.5d-2P are marked with ×.

(Amended edition, Amendment No. 4)

Example of designation of a Design 1 stud with thread diameter d=16 mm, coarse pitch P=2 mm, tolerance class 6g, length l=120 mm, property class 5.8, without coating:

Stud M16 - 6g×120.58 GOST 22033-76

Same, Design 2 with fine pitch P=1.5 mm, property class 10.9, made of steel grade 40Kh, with coating 02, thickness 6 µm:

Stud 2 M16×1.5-6g×120.109.40Kh.026 GOST 22033-76

Same, with fine pitch P=1.5 mm, tolerance class 3n(3) on the threaded end, coarse pitch P=2 mm, tolerance class 6g on the nut end, property class 6.6, with coating 05:

Stud M16××120.66.05 GOST 22033-76

(Revised edition, Amendment No. 1, No. 2, No. 4).

3. Thread — per GOST 24705-81.

3a. Thread runout dimensions — per GOST 27148-86.

3b. Dimensional tolerances, form and position deviations of surfaces, inspection methods — per GOST 1759.1-82.

3c. Surface defects and inspection methods for studs — per GOST 1759.2-82.

1–3. (Amended edition, Amendments No. 3, No. 4).

4. The surface of the smooth shank portion d₁ is not machined when studs are manufactured from calibrated bar stock.

5. (Deleted, Amendment No. 2).

6. By agreement between the manufacturer and the customer, it is permitted to produce an interference-fit thread per GOST 4608-81 on the threaded end of the stud, with this indicated in the stud designation; such studs shall be marked on the end face of the nut end with Arabic numerals indicating the thread sorting group of the stud per GOST 4608-81.

(Amended edition, Amendment No. 3).

7. Technical requirements — per GOST 1759.0-87

(Amended, Amendment No. 4).

8. The theoretical mass of studs is given in Reference Appendices 1 and 2.

APPENDIX 1

For reference

Stud length l, mm	Theoretical mass of 1000 pcs of steel Type 1 studs, kg, with coarse thread pitch, for nominal thread diameter d, mm
	2	2.5	3	4	5	6	8	10	12	(14)	16	(18)	20	(22)	24	(27)	30	(33)	36	(39)	42	(45)	48
10	0.255	0.408	0.596	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
12	0.304	0.485	0.707	1.345	2.300	3.450	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
14	0.341	0.536	0.784	1.459	2.560	3.807	7.690	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
16	0.391	0.613	0.884	1.635	2.720	4.064	7.949	13.52	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
(18)	0.440	0.690	0.995	1.790	2.968	4.417	8.586	14.52	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
20	0.489	0.768	1.106	1.987	3.215	4.770	9.223	15.52	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
(22)	0.539	0.845	1.217	2.185	3.523	5.214	10.010	16.76	27.48	38.16	-	-	-	-	-	-	-	-	-	-	-	-	-
25	0.613	0.960	1.383	2.480	3.986	5.789	11.040	18.38	28.04	40.28	57.50	-	-	-	-	-	-	-	-	-	-	-	-
(28)	0.687	1.076	1.549	2.776	4.448	6.455	12.080	20.00	30.38	43.48	61.53	81.06	-	-	-	-	-	-	-	-	-	-	-
30	0.736	1.153	1.661	2.974	4.756	6.899	12.710	21.00	31.84	45.47	64.19	84.38	-	-	-	-	-	-	-	-	-	-	-
(32)	0.785	1.230	1.772	3.171	5.065	7.343	13.500	22.01	33.29	47.46	-	-	-	-	-	-	-	-	-	-	-	-	-
35	0.859	1.346	1.938	3.467	5.527	8.008	14.690	23.63	35.64	50.66	70.17	90.73	-	-	-	-	-	-	-	-	-	-	-
(38)	0.933	1.461	2.104	3.763	5.989	8.674	15.870	25.48	37.98	53.85	74.41	96.03	-	-	-	-	-	-	-	-	-	-	-
40	0.982	1.538	2.215	3.960	6.298	9.118	16.660	26.71	39.43	55.84	77.08	99.34	128.7	-	-	-	-	-	-	-	-	-	-
(42)	1.032	1.615	2.326	4.157	6.606	9.562	17.450	27.95	41.21	57.83	79.74	102.60	132.9	-	-	-	-	-	-	-	-	-	-
45	1.106	1.731	2.493	4.453	7.068	10.230	18.630	29.80	43.87	61.03	83.98	107.90	139.5	176.2	212.9	-	-	-	-	-	-	-	-
(48)	1.180	1.846	2.659	4.749	7.531	10.890	19.820	31.65	46.54	64.66	87.73	112.60	145.4	183.4	221.4	-	-	-	-	-	-	-	-
50	1.229	1.924	2.770	4.947	7.839	11.340	20.600	32.88	48.31	67.07	90.89	116.50	150.3	189.4	228.4	-	-	-	-	-	-	-	-
55	1.352	2.116	3.048	5.439	8.610	12.450	22.580	35.96	52.75	73.12	98.78	125.20	161.1	202.6	244.0	325.4	-	-	-	-	-	-	-
60	1.476	2.309	3.325	5.933	9.380	13.560	24.550	39.04	57.19	79.16	106.70	135.10	171.9	215.8	259.6	345.4	437.9	-	-	-	-	-	-
65	1.599	2.502	3.603	6.426	10.150	14.670	26.520	42.13	61.63	85.20	114.60	145.10	184.2	229.0	275.1	365.3	462.4	-	-	-	-	-	-
70	1.722	2.694	3.880	6.919	10.920	15.780	28.500	45.21	66.07	91.24	122.40	155.10	196.6	243.9	290.6	385.3	486.9	629.2	746.9	-	-	-	-
75	1.846	2.887	4.158	7.413	11.690	16.890	30.470	48.29	70.51	97.28	130.30	165.10	208.9	258.9	308.4	404.0	509.8	655.0	780.2	-	-	-	-
80	1.969	3.080	4.435	7.906	12.460	17.990	32.440	51.37	74.95	103.30	138.20	175.10	221.2	273.8	326.2	426.5	537.6	684.1	820.2	1007	1178	1430	1618
85	-	3.272	4.712	8.399	13.230	19.110	34.420	54.46	79.39	109.40	146.10	185.10	233.6	288.7	343.9	448.9	560.4	713.1	853.4	1048	1223	1475	1677
90	-	3.465	4.990	8.892	14.000	20.220	36.390	57.54	83.82	115.40	153.00	195.10	245.9	303.7	361.6	471.4	588.2	742.2	886.7	1089	1269	1530	1737
(95)	-	3.658	5.267	9.386	14.77	21.32	38.36	60.62	88.26	121.4	161.9	205.1	258.3	318.6	379.4	493.9	615.9	771.2	923.3	1130	1319	1584	1803
100	-	3.850	5.545	9.879	15.55	22.43	40.33	63.70	92.70	127.5	169.8	215.1	270.5	333.5	397.2	516.4	643.7	800.3	959.9	1171	1366	1639	1865
(105)	-	4.043	5.822	10.370	16.32	23.54	42.31	66.79	97.14	133.5	177.7	225.1	282.9	348.4	414.9	538.9	671.4	829.3	1000.0	1216	1413	1694	1926
110	-	4.236	6.100	10.860	17.09	24.65	44.28	69.87	101.60	139.6	185.6	235.1	295.2	365.3	432.7	561.3	699.2	858.4	1039.0	1253	1460	1748	1988
(115)	-	4.428	6.378	11.360	17.86	25.76	46.25	72.95	106.00	145.6	193.5	245.1	307.5	378.3	450.5	583.8	726.9	887.4	1080.0	1294	1515	1803	2059
120	-	4.621	6.654	11.850	18.63	26.87	48.22	76.04	110.40	151.6	201.4	255.1	319.9	393.2	468.2	606.3	754.7	916.5	1120.0	1334	1569	1867	2111
130	-	5.006	7.209	12.840	20.17	29.09	52.17	82.20	119.30	163.7	217.2	274.9	344.5	423.0	503.7	651.2	810.1	976.4	1200.0	1416	1678	1967	2250
140	-	5.392	7.764	13.820	21.71	31.31	56.12	88.37	128.20	175.8	232.9	294.9	369.2	452.9	539.2	696.2	865.6	1034.2	1279.0	1487	1786	2076	2392
150	-	5.777	8.319	14.810	23.25	33.53	60.06	94.53	137.10	187.9	248.7	314.9	393.9	482.7	574.7	741.1	921.1	1092.5	1359.0	1579	1895	2185	2534
160	-	6.162	8.874	15.800	24.79	35.75	64.01	100.00	145.00	198.7	263.0	332.8	416.2	510.0	606.9	782.3	971.8	1150.7	1433.0	1660	1995	2295	2665
170	-	-	-	-	-	-	67.95	106.20	153.90	210.8	278.8	352.8	440.9	539.8	642.4	827.2	1027.0	1208.0	1513.0	1742	2104	2404	2807
180	-	-	-	-	-	-	71.90	112.30	162.80	222.9	294.6	372.8	465.5	569.6	678.0	872.2	1083.0	1266.9	1592.0	1824	2213	2513	2948
190	-	-	-	-	-	-	75.85	118.50	171.70	234.9	310.4	392.8	490.2	599.5	713.5	917.1	1138.0	1325.0	1672.0	1906	2321	2622	3091
200	-	-	-	-	-	-	79.79	124.70	180.50	247.0	326.2	412.7	514.9	629.4	748.9	962.1	1194.0	1383.1	1752.0	1988	2430	2732	3233
220	-	-	-	-	-	-	-	-	198.30	271.2	357.7	452.7	564.2	689.0	820.0	1052.0	1305.0	1497.6	1912.0	2151	2648	2950	3517
240	-	-	-	-	-	-	-	-	-	-	-	-	613.5	748.7	891.0	1142.0	1416.0	1613.8	2072.0	2314	2865	3169	3801
260	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	1232.0	1527.0	1730.0	2232.0	2478	3083	3394	4085
280	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	1846.0	2391.0	2641	3300	3606	4369
300	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	1962.0	2551.0	2845	3518	3825	4653

Note. To determine the mass of studs manufactured from other materials, the mass values given in the table shall be multiplied by the factor: 0.356 for aluminium alloy; 0.970 for bronze; 1.080 for brass.

(Amended edition, Amendment No. 4)

APPENDIX 2

For reference

10

Stud length l, mm	Theoretical mass of 1000 pcs of steel Type 2 studs, kg, with coarse thread pitch, for nominal thread diameter d, mm
	2	2.5	3	4	5	6	8	12	(14)	16	(18)	20	(22)	24	(27)	30	(33)	36	(39)	42	(45)	48
10	0.243	0.390	0.573	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
12	0.280	0.451	0.661	1.243	2.103	3.236	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
14	0.317	0.511	0.750	1.394	2.351	3.596	7.03	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
16	0.354	0.571	0.838	1.549	2.597	3.880	7.641	13.05	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
(18)	0.392	0.631	0.926	1.704	2.845	4.233	8.278	14.06	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
20	0.429	0.691	1.014	1.859	3.092	4.586	8.915	15.06	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-
(22)	0.466	0.751	1.102	2.014	3.339	4.939	9.552	16.07	26.37	35.79	-	-	-	-	-	-	-	-	-	-	-	-	-
25	0.522	0.841	1.235	2.246	3.710	5.468	10.507	17.57	26.91	38.77	54.62	-	-	-	-	-	-	-	-	-	-	-	-
(28)	0.578	0.931	1.367	2.478	4.081	5.997	11.462	19.08	29.09	41.75	58.62	76.27	-	-	-	-	-	-	-	-	-	-	-
30	0.616	0.991	1.455	2.633	4.329	6.350	12.099	20.08	30.54	43.74	61.28	79.59	-	-	-	-	-	-	-	-	-	-	-
(32)	0.653	1.052	1.543	2.788	4.576	6.702	12.735	21.09	32.00	45.73	-	-	-	-	-	-	-	-	-	-	-	-	-
35	0.709	1.142	1.676	3.020	4.947	7.232	13.691	22.59	34.18	48.71	67.92	87.59	-	-	-	-	-	-	-	-	-	-	-
(38)	0.765	1.232	1.808	3.253	5.318	7.761	14.646	24.10	36.36	51.69	71.92	92.54	-	-	-	-	-	-	-	-	-	-	-
40	0.802	1.292	1.896	3.407	5.566	8.113	15.283	25.10	37.81	53.68	74.58	95.85	124.9	-	-	-	-	-	-	-	-	-	-
(42)	0.840	1.352	1.984	3.562	5.813	8.466	15.919	26.11	39.27	55.67	77.24	99.15	129.0	-	-	-	-	-	-	-	-	-	-
45	0.896	1.442	2.117	3.795	6.184	8.995	16.875	27.61	41.45	58.65	81.24	104.11	135.3	171.4	206.8	-	-	-	-	-	-	-	-
(48)	0.952	1.532	2.249	4.027	6.555	9.525	17.830	29.12	43.63	61.63	85.23	109.07	141.5	179.1	215.7	-	-	-	-	-	-	-	-
50	0.989	1.592	2.337	4.182	6.802	9.877	18.467	30.12	45.09	63.62	87.90	112.37	145.7	184.2	221.7	-	-	-	-	-	-	-	-
55	1.082	1.743	2.558	4.569	7.421	10.759	20.058	32.63	48.72	68.59	94.56	120.64	156.1	197.0	236.7	317.1	-	-	-	-	-	-	-
60	1.175	1.893	2.778	4.956	8.039	11.641	21.650	35.14	52.36	73.56	101.22	128.90	16.5	209.8	251.7	336.4	426.4	-	-	-	-	-	-
65	1.269	2.043	2.998	5.343	8.658	12.532	23.242	37.65	55.99	78.53	107.87	137.16	176.9	222.6	266.7	355.8	450.1	-	-	-	-	-	-
70	1.362	2.193	3.219	5.731	9.276	13.405	24.834	40.16	59.63	83.50	114.53	145.43	187.3	235.4	281.7	375.1	473.8	611.0	728.8	-	-	-	-
75	1.455	2.343	3.439	6.118	9.894	14.287	26.426	42.67	63.26	88.47	121.19	153.69	197.7	248.2	296.6	394.5	497.4	627.5	763.2	-	-	-	-
80	1.549	2.494	3.660	6.505	10.513	15.169	28.018	45.18	66.90	93.44	127.85	161.95	208.1	261.0	311.6	413.8	521.1	656.6	797.5	972	1148	1366	1580
85	-	2.644	3.880	6.892	11.131	16.050	29.610	47.69	70.54	98.41	134.51	170.21	218.5	273.8	326.6	433.1	544.8	685.7	831.9	1013	1195	1421	1641
90	-	2.794	4.101	7.280	11.749	16.932	31.202	50.20	74.17	103.38	141.17	178.48	228.9	286.6	341.6	452.5	568.5	714.7	866.3	1054	1242	1475	1703
(95)	-	2.944	4.321	7.667	12.368	17.814	32.794	52.71	77.81	108.35	147.83	186.74	239.3	299.3	356.6	471.8	592.2	743.8	900.7	1095	1280	1530	1765
100	-	3.094	4.542	8.054	12.986	18.696	34.386	55.22	81.44	113.32	154.49	195.00	249.7	312.1	371.6	491.1	615.9	972.8	935.0	1135	1336	1585	1827
(105)	-	3.245	4.762	8.441	13.605	19.578	35.978	57.73	85.08	118.29	161.15	203.26	260.1	324.9	386.5	510.5	639.6	802.9	969.4	1176	1383	1639	1888
110	-	3.395	4.983	8.828	14.223	20.460	37.570	60.24	88.72	123.26	167.81	211.53	270.5	337.7	401.5	529.8	663.2	830.9	1003.8	1217	1430	1694	1950
(115)	-	3.545	5.203	9.216	14.841	21.342	39.162	62.75	92.35	128.24	174.76	219.79	280.9	350.5	416.5	549.1	686.9	860.0	1038.2	1258	1477	1748	2012
120	-	3.695	5.424	9.603	15.460	22.224	40.457	65.26	95.99	133.21	181.12	228.05	291.3	363.3	431.5	568.5	710.6	889.1	1072.5	1299	1524	1803	2073
130	-	3.996	5.865	10.337	16.697	23.988	43.937	70.28	103.26	143.15	194.44	244.58	312.1	388.9	461.4	607.1	758.0	947.1	1141.3	1381	1619	1912	2197
140	-	4.296	6.306	11.152	17.933	25.751	47.121	75.31	110.53	153.09	207.76	261.10	332.9	414.5	491.4	645.8	805.4	1005.2	1210.0	1462	1713	2022	2320
150	-	4.597	6.747	11.926	19.170	27.515	50.305	80.33	117.80	163.03	221.08	277.63	353.8	440.1	521.4	684.5	852.7	1063.4	1278.8	1544	1807	2131	2444
160	-	4.897	7.187	12.700	20.407	29.279	53.489	85.35	125.07	172.97	234.39	294.15	374.6	465.6	551.3	723.2	900.1	1121.4	1347.5	1626	1901	2240	2567
170	-	-	-	-	-	-	56.673	90.37	132.35	182.91	247.71	310.68	395.4	491.2	581.3	761.8	947.5	1179.6	1416.3	1707	1995	2349	2690
180	-	-	-	-	-	-	59.857	95.39	139.62	192.85	261.03	327.21	416.2	516.8	611.3	800.5	994.9	1237.7	1485.0	1789	2089	2459	2814
190	-	-	-	-	-	-	63.041	100.41	146.89	202.79	274.35	343.73	437.0	542.4	641.2	839.2	1042.2	1295.8	1553.8	1872	2183	2568	2937
200	-	-	-	-	-	-	66.225	105.43	154.16	212.73	287.67	360.26	457.8	568.0	671.2	877.8	1089.6	1353.9	1622.5	1952	2277	2677	3061
220	-	-	-	-	-	-	-	-	168.71	232.61	314.30	393.31	499.4	619.2	731.1	955.2	1184.4	1470.1	1760.0	2116	2465	2896	3308
240	-	-	-	-	-	-	-	-	-	-	-	-	541.0	670.3	791.0	1032.5	1279.1	1586.4	1897.6	2279	2654	3114	3554
260	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	1109.9	1373.9	1703.0	2035.1	2442	2842	3333	3801
280	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	1820.0	2172.6	2606	3030	3551	4048
300	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	-	1935.0	2310.1	2769	3218	3770	4295

Note. To determine the mass of studs made from other materials, the mass values given in the table shall be multiplied by the coefficient: 0.356 for aluminium alloy; 0.970 for bronze; 1.080 for brass.

(Amended edition, Amendment No. 4)

Corresponds to DIN 938.