GOST 13014-80 (ST SEV 777-77) Rolling Bearing Adapter Sleeves

GOST 13014-80

(ST SEV 777-77)

Group G16

State Standard of the Union of Soviet Socialist Republics

ADAPTER SLEEVES FOR ROLLING BEARINGS

Main dimensions

Withdrawal sleevs of rolling bearings.

Basic dimensions

Effective from 01.01.81

to 01.01.91*

---

• The validity period restriction was lifted by Resolution

of the USSR Gosstandart dated 22.07.91 No. 1279

(IUS No. 10, 1991). — Note by “KODEKS”

DEVELOPED BY the Ministry of Automotive Industry

DRAFTED BY

T.P. Klyubina (project lead); L.G. Dorofeeva

SUBMITTED BY the Ministry of Automotive Industry

Board Member B.G. Shakhnazarov

APPROVED AND PUT INTO EFFECT by Resolution of the USSR State Committee for Standards dated 24 April 1980 No. 1860

SUPERSEDES GOST 13014-67

1. This standard applies to adapter sleeves intended for mounting rolling bearings with a tapered bore of 1:12 taper onto cylindrical shaft journals, and establishes their basic dimensions.

This standard fully complies with ST SEV 777-77.

2. The designations and dimensions of the sleeves shall conform to those shown in the drawing and in Tables 1-6.

Dimensions and are valid for sleeves in the uncut state.

• nominal diameter of the bearing’s tapered bore; - nominal diameter of the bore

of the adapter sleeve; - outer diameter of the adapter sleeve thread; - length of the adapter sleeve;

• distance from the bearing face to the adapter sleeve face before press-fitting;

• width of the threaded collar.

3. Sleeves shall be made of steel with a tensile strength of not less than 400 N/mm.

4. By agreement between the manufacturer and the consumer, sleeves may be supplied with nuts.

5. Basic dimensions of nuts - as per GOST 8725-67.

6. Technical requirements for sleeve seating surfaces - as per GOST 3325-55.

Table 1

Sleeves for bearings of diameter series 2, width series 0

Dimensions in mm

Sleeve designation							Weight, kg
AN 208	40	35	M 45x1.5	25	2	6	0.094
AN 209	45	40	M 50×1.5	26	3	6	0.104
AN 210	50	45	M 55×2	28	3	7	0.130
AN 211	55	50	M 60×2	29	3	7	0.167
AN 212	60	55	M 65×2	32	3	8	0.175
AN 213	65	60	M 75×2	32.5	3.5	8	0.242
AN 214	70	65	M 80x2	33.5	3.5	8	0.255
AN 215	75	70	M 85×2	34.5	3.5	8	0.280
AN 216	80	75	M 90×2	35.5	3.5	8	0.306
AN 217	85	80	M 95x2	38.5	3.5	9	0.353
AN 218	90	85	M 100x2	40	4	9	0.427
AN 220	100	95	M 110×2	45	4	10	0.525
AN 222	110	105	M 120×2	50	4	11	0.647
AN 224	120	115	M 130×2	53	4	12	0.755
AN 226	130	125	M 140×2	53	4	12	0.815
AN 228	140	135	M 150×2	56	5	13	1.007
AN 230	150	145	M 160×3	60	5	14	1.155
AN 232	160	150	M 170x3	64	5	15	1.910
AN 234	170	160	M 180×3	69	5	16	2.210
AN 236	180	170	M 190×3	69	5	16	2.340
AN 238	190	180	Tr 205×4	73	5	17	2.940
AN 240	200	190	Tg 215x4	77	5	18	3.120
AN 244	220	200	Tr 235×4	85	6	18	6.100
AN 248	240	220	Tr 260x4	96	6	22	8.160
AN 252	260	340	Tr 280×4	105	6	23	9.885
AN 256	280	260	Tg 300x4	105	8	23	10.440

Table 2

Sleeves for bearings of diameter series 2(5), width series 0

Dimensions in mm

Sleeve designation							Weight, kg
AN 308	40	35	M 45×1.5	29	3	6	0.090
AN 309	45	40	M 50x1.5	31	3	6	0.109
AN 310X	50	45	M 55×2	35	3	7	0.137
AN 311X	55	50	M 60×2	37	3	7	0.161
AN 312X	60	55	M 65×2	40	3	8	0.189
AN 313	65	60	M 75×2	42	3	8	0.253
AN 314	70	65	M 80x2	43	4	8	0.280
AN 315	75	70	M 85×2	45	4	8	0.313
AN 316	80	75	M 90×2	48	4	8	0.365
AN 317X	85	80	M 95×2	52	4	9	0.429
AN 318X	90	85	M 100x2	53	4	9	0.461
AN 320X	100	95	M 110×2	59	4	10	0.582
AN 322X	110	105	M 120×2	63	4	12	0.663
AN 324X	120	115	M 130×2	69	4	13	0.866
AN 326X	130	125	M 140×2	74	4	14	1.020
AN 328X	140	135	M 150x2	77	5	14	1.16
AN 330X	150	145	M 165×3	83	5	15	1.50
AN 332	160	150	M 180×3	88	5	16	2.69
AN 334	170	160	M 190x3	93	5	17	3.07
AN 2236	180	170	M 200×3	105	5	17	3.73
AN 2238	190	180	Tr 210x4	112	5	18	4.25
AN 2240	200	190	Tr 220x4	118	5	19	4.68
AN 2244	220	200	Tr 240x4	130	6	20	9.10
AN 2248	240	220	Tr 260x4	144	6	21	11.10
AN 2252	260	240	Tr 290×4	155	6	23	14.00
AN 2256	280	260	Tr 310×5	155	8	24	15.20
AN 2260	300	280	Tg 330×5	170	8	26	18.10
AN 2264	320	300	Tr 350×5	180	10	27	20.20

Table 3

Sleeves for bearings, diameter series 3 (6), width series 0

Dimensions in mm

Sleeve designation							Weight, kg
AN 2308	40	35	M 45x1.5	40	3	7	0.128
AN 2309	45	40	M 50x1.5	44	3	7	0.164
AN 2310Kh	50	45	M 55x2	50	3	9	0.209
AN 2311X	55	50	M 60x2	54	3	10	0.253
AN 2312Kh	60	55	M 65×2	58	3	11	0.297
AN 2313	65	60	M 75x2	61	3	12	0.395
AN 2314Kh	70	65	M 80×2	64	4	12	0.466
AN 2315Kh	75	70	M 85×2	68	4	12	0.534
AN 2316Kh	80	75	M 90×2	71	4	12	0.597
AN 2317Kh	85	80	M 95×2	74	4	13	0.670
AN 2318Kh	90	85	M 100×2	79	4	14	0.779
AN 2320Kh	100	95	M 110×2	90	4	16	0.998
AN 2322Kh	110	105	M 125×2	98	4	16	1.350
AN 2324Kh	120	115	M 135×2	105	4	17	1.60
AN 2326Kh	130	125	M 145×2	115	4	19	1.97
AN 2328Kh	140	135	M 155×3	125	5	20	2.33
AN 2330Kh	150	145	M 165×3	135	5	24	2.82
AN 2332	160	150	M 180x3	140	6	24	4.72
AN 2334	170	160	M 190x3	146	6	24	5.25
AN 2336	180	170	M 200x3	154	6	26	5.83
AN 2338	190	180	Tg 210x4	160	7	26	6.63
AN 2340	200	190	Tg 220×4	170	7	30	7.54
AN 2344	220	200	Tg 240x4	181	8	30	13.50
AN 2348	240	220	Tg 260x4	189	8	30	15.50
AN 2352	260	240	Tg 290×4	205	8	30	19.60
AN 2356	280	260	Tg 310x5	212	8	30	21.60

Table 4

Sleeves for bearings, diameter series 1, width series 3

Dimensions in mm

Sleeve designation							Weight, kg
AN 3024Kh	120	115	M 130x2	60	4	13	0.75
AN 3026Kh	130	125	M 140×2	67	4	14	0.93
AN 3028Kh	140	135	M 150x2	68	5	14	1.01
AN 3030Kh	150	145	M 160x3	72	5	15	1.15
AN 3032	160	150	M 170×3	77	5	16	2.06
AN 3034	170	160	M 180x3	85	5	17	2.43
AN 3036	180	170	M 190x3	92	6	17	2.81
AN 3038	190	180	Tg 205×4	96	6	18	3.32
AN 3040	200	190	Tg 215x4	102	6	19	3.80
AN 3044	220	200	Tg 235×4	111	6	20	7.40
AN 3048	240	220	Tg 260x4	116	7	21	8.75
AN 3052	260	240	Tg 280×4	128	7	23	10.70
AN 3056	280	260	Tg 300x4	131	8	24	12.00
AN 3060	300	280	Tg 320×5	145	8	26	14.40
AN 3064	320	300	Tg 345×5	149	8	27	16.00
AN 3068	340	320	Tg 365×5	162	9	28	19.5
AN 3072	360	340	Tg 385×5	167	9	30	21.0
AN 3076	380	360	Tg 410×5	170	10	31	23.2
AN 3080	400	380	Tg 430×5	183	10	33	27.3
AN 3084	420	400	Tg 450×5	186	10	34	29.0
AN 3088Kh	440	420	Tg 470×5	194	11	35	32.0
AN 3092Kh	460	440	Tg 490×5	202	11	37	35.2
AN 3096Kh	480	460	Tg 520×6	205	12	38	39.2
AN 30/500Kh	500	480	Tg 540×6	209	12	40	42.5
AN 30/530	530	500	Tg 560×6	230	12	45	61.9
AN 30/560	560	530	Tg 590×6	240	12	45	68.6
AN 30/600	600	570	Tg 630×6	245	14	45	75.4
AN 30/630	630	600	Tg 670×6	258	14	46	87.8
AN 30/670	670	630	Tg 710×7	280	14	50	124.0

Table 5

Bushings for bearings of diameter series 7, width series 3

Dimensions in mm

Sleeve designation							Weight, kg
AN 3120Kh	100	95	M 110×2	64	4	11	0.65
AN 3122Kh	110	105	M 120×2	68	4	11	0.76
AN 3124Kh	120	115	M 130x2	75	4	12	0.95
AN 3126Kh	130	125	M 140×2	78	4	12	1.08
AN 3128Kh	140	135	M 150×2	83	5	14	1.28
AN 3130Kh	150	145	M 165×3	96	5	15	1.79
AN 3132	160	150	M 180×3	103	5	16	3.21
AN 3134	170	160	M 190x3	104	5	16	3.40
AN 3136	180	170	M 200x3	116	6	19	4.22
AN 3138	190	180	Tr 210×4	125	6	20	4.89
AN 3140	200	190	Tr 220x4	134	6	21	5.49
AN 3144	220	200	Tr 240x4	145	6	23	10.40
AN 3148	240	220	Tr 260x4	154	7	25	12.00
AN 3152	260	240	Tr 290x4	172	7	26	16.20
AN 3156	280	260	Tr 310x5	175	8	28	17.50
AN 3160	300	280	Tr 330x5	192	8	30	20.8
AH 3164	320	300	Tr 350×5	209	8	31	24.5
AN 3168	340	320	Tr 370×5	225	9	33	29.0
AN 3172	360	340	Tr 400x5	229	9	35	33.0
AN 3176	380	360	Tr 420x5	232	10	36	35.7
AN 3180	400	380	Tr 440x5	240	10	38	39.5
AH 3184	420	400	Tr 460x5	266	10	40	46.5
AN 3188Kh	440	420	Tr 480x5	270	11	42	49.8
AN 3192Kh	460	440	Tr 510x6	285	11	43	57.9
AN 3196Kh	480	460	Tr 530x6	295	12	45	63.1
AN 31/500X	500	480	Tr 550×6	313	12	47	70.9
AN 31/530	530	500	Tr 560×6	325	12	53	93.4
AN 31/560	560	530	Tr 590×6	335	12	55	102.0
AN 31/600	600	570	Tr 630x6	355	14	55	118.0
AN 31/630	630	600	Tr 670x6	375	14	60	138.0
AN 31/670	670	630	Tr 710x7	395	14	60	187.0

Table 6

Sleeves for bearings, diameter series 1, width series 3

Dimensions in mm

Sleeve designation							Weight, kg
AN 3218Kh	90	85	M 100×2	63	4	10	0.576
AN 3220Kh	100	95	M 110×2	73	4	11	0.767
AN 3222Kh	110	105	M 125×2	82	4	11	1.040
AN 3224Kh	120	115	M 135×2	90	4	13	1.300
AN 3226Kh	130	125	M 145x2	98	4	15	1.580
AN 3228Kh	140	135	M 155×3	104	5	15	1.840
AN 3230Kh	150	145	M 165×3	114	5	17	2.220
AN 3232	160	150	M 180x3	124	6	20	4.080
AN 3234	170	160	M 190x3	134	6	24	4.800
AN 3236	180	170	M 200x3	140	6	25	5.320
AN 3238	190	180	Tr 210x4	145	7	25	5.900
AN 3240	200	190	Tr 220x4	153	7	24	6.680
AN 3260	300	280	Tr 330x5	228	8	34	26.000
AN 3264	320	300	Tr 350x5	246	8	36	30.600
AN 3268	340	320	Tr 370x5	264	9	38	35.4
AN 3272	360	340	Tr 400x5	274	9	40	41.5
AN 3276	380	360	Tr 420x5	284	10	42	45.6
AN 3280	400	380	Tr 440x5	302	10	44	51.7
AN 3284	420	400	Tr 460x5	321	10	46	58.9
AN 3288Kh	440	420	Tr 480x5	330	11	48	63.8
AN 3292Kh	460	440	Tr 510x6	349	11	50	74.5
AN 3296Kh	480	460	Tr 530x6	364	12	52	82.1
AN 32/500Kh	500	480	Tr 550×6	393	12	54	94.6

Note. Tables 1-6 give the mass of the sleeves (without nut), calculated using a material density of 7.85 kg/dm³. Example of the designation of an adapter sleeve for bearings with a bore diameter =320 mm, diameter series 2, width series 3

Adapter sleeve AN 3264 GOST 13014-80

7. A comparison of sleeve designations under GOST 13014-80 and the previously effective regulatory and technical documentation is given in the informative appendix.

APPENDIX (informative)

Appendix

For reference

Designation of sleeves according to
GOST 13014-80	previously effective regulatory and technical documentation
AN 308	VS 208
AN 309	VS 209
AN 310X	VS 210
AN 311Kh	VS 211
AN 312X	VS 212
AN 313	VS 213
AN 314	VS 214
AN 315	VS 215
AN 316	VS 216
AN 317X	VS 217
AN 318X	VS 218
AN 320X	VS 220
AN 322X	VS 222
AN 324X	VS 224
AN 326X	VS 226
AN 328X	VS 228
AN 330X	VS 230
AN 332	VS 232
AN 334	VS 234
AN 2236	VS 236
AN 2308	VS 308
AN 2309	VS 309
AN 2310Kh	VS 310
AN 2311X	VS 311
AN 2312Kh	VS 312
AN 2313	VS 313
AN 2314Kh	VS 314
AN 2315Kh	VS 315
AN 2316Kh	VS 316
AN 2317Kh	VS 317
AN 2318Kh	VS 318
AN 2320Kh	VS 320
AN 2322Kh	VS 322
AN 2324Kh	VS 324
AN 2326Kh	VS 326
AN 2328Kh	VS 328
AN 2330Kh	VS 330
AN 2332	VS 332
AN 2334	VS 334
AN 2336	VS 336
AN 3024Kh	VS 124
AN 3026Kh	VS 126
AN 3028Kh	VS 128
AN 3030Kh	VS 130
AN 3032	VS 132
AN 3034	VS 134
AN 3036	VS 136
AN 3120Kh	VS 720
AN 3122Kh	VS 722
AN 3124Kh	VS 724
AN 3126Kh	VS 726
AN 3128Kh	VS 728
AN 3130Kh	VS 730
AN 3132	VS 732
AN 3134	VS 734
AN 3136	VS 736
AN 3218Kh	VS 518
AN 3220Kh	VS 520
AN 3222Kh	VS 522
AN 3224Kh	VS 524
AN 3226Kh	VS 526
AN 3228Kh	VS 528
AN 3230Kh	VS 530
AN 3232	VS 532
AN 3234	VS 534
AN 3236	VS 536